Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:evo:carb01a [2020/05/10 03:54] hippysmack [Float] |
techtalk:evo:carb01a [2022/03/25 01:31] hippysmack [Jets] |
||
---|---|---|---|
Line 23: | Line 23: | ||
It should be tapped out from the rounded top pedestal toward the square top pedestal with a small punch or even better, a spring loaded center punch. \\ | It should be tapped out from the rounded top pedestal toward the square top pedestal with a small punch or even better, a spring loaded center punch. \\ | ||
Install the pin in the same fashion just in reverse (from the loose side toward the rounded pedestal). \\ | Install the pin in the same fashion just in reverse (from the loose side toward the rounded pedestal). \\ | ||
+ | When removing or installing the float pin, be careful not to break the pedestal(s). \\ | ||
+ | If the pedestal(s) is broken, the carburetor will have to be replaced. \\ | ||
+ | |||
+ | Float pin (27575-88) will not fit the new carburetor. A new float pin (27575-88A) will fit all H-D CV carburetors. \\ | ||
+ | This new part will supersede the current part. \\ | ||
{{:techtalk:evo:carb:removing_keihin_cv_float_bowl_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:removing_keihin_cv_float_bowl_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:removing_keihin_cv_float_bowl_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:carb:removing_keihin_cv_float_bowl_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:removing_keihin_cv_float_bowl_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:removing_keihin_cv_float_bowl_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
Line 79: | Line 84: | ||
==== Jets ==== | ==== Jets ==== | ||
Generally, the jets can be blown out with compressed air unless they have been sitting for a few years getting gunked up. \\ | Generally, the jets can be blown out with compressed air unless they have been sitting for a few years getting gunked up. \\ | ||
- | If need be, you can run a welding tip cleaner into the holes to clear out varnish / debris that may be stuck there. \\ | ||
- | **Caution**: Only use a rod that is smaller than the holes being rodded and go very easy when inserting to keep from widening the jets. \\ | ||
- | {{:techtalk:evo:carb:keihin_cv_dismantle_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:keihin_cv_dismantle_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:keihin_cv_dismantle_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
- | |||
- | {{:techtalk:evo:carb:keihin_cv_dismantle_10_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:keihin_cv_dismantle_11_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:carb:keihin_cv_dismantle_15_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
=== Air / Fuel Mixture Screw and Packing === | === Air / Fuel Mixture Screw and Packing === |