Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Next revision Both sides next revision | ||
techtalk:evo:elec01 [2019/11/11 06:13] ixl2relax [5 Volt Sensor Supply] |
techtalk:evo:elec01 [2019/11/11 06:17] ixl2relax [5 Volt Sensor Supply] |
||
---|---|---|---|
Line 266: | Line 266: | ||
\\ | \\ | ||
- | | **1998-2003 Sport Ignition Control Module**\\ \\ ICM GRAY Connector Pin 1 is +5v Output (RED/White Wire)\\ ICM GRAY Connector Pin 8 is Sensor Ground (BLACK/White Wire) | 1998-?\\ MAP Sensor Connector 80B - Pin 1 - 5v Sensor Power (R/W Wire)\\ MAP Sensor Connector 80B - Pin 3 - Sensor Ground (B/W Wire)\\ CAM Sensor Connector 14B - Pin A - 5v Sensor Power (R/W Wire)\\ CAM Sensor Connector 14B - Pin C - Sensor Ground (B/W Wire)\\ \\ ?-2003\\ MAP Sensor Connector 80B - Pin C - 5v Sensor Power (R/W Wire)\\ MAP Sensor Connector 80B - Pin A - Sensor Ground (B/W Wire)\\ CAM Sensor Connector 14B - Pin A - 5v Sensor Power (R/W Wire)\\ CAM Sensor Connector 14B - Pin C - Sensor Ground (B/W Wire) | | + | | **1998-2003 Sport Ignition Control Module**\\ \\ ICM GRAY Connector Pin 1 is +5v Output (RED/White Wire)\\ ICM GRAY Connector Pin 8 is Sensor Ground (BLACK/White Wire)\\ \\ \\ \\ 1998-2003 models other than the Sport model\\ do not produce or utilize 5v power. | 1998-?\\ MAP Sensor Connector 80B - Pin 1 - 5v Sensor Power (R/W Wire)\\ MAP Sensor Connector 80B - Pin 3 - Sensor Ground (B/W Wire)\\ CAM Sensor Connector 14B - Pin A - 5v Sensor Power (R/W Wire)\\ CAM Sensor Connector 14B - Pin C - Sensor Ground (B/W Wire)\\ \\ ?-2003\\ MAP Sensor Connector 80B - Pin C - 5v Sensor Power (R/W Wire)\\ MAP Sensor Connector 80B - Pin A - Sensor Ground (B/W Wire)\\ CAM Sensor Connector 14B - Pin A - 5v Sensor Power (R/W Wire)\\ CAM Sensor Connector 14B - Pin C - Sensor Ground (B/W Wire) | |
| **2004-2006 Engine Control Module**\\ \\ ICM Connector Pin 3 is +5v Output (RED/White Wire)\\ ICM Connector Pin 4 is Sensor Ground (BLACK/White Wire) | MAP Sensor Connector 80B - Pin C - 5v Sensor Power (R/W Wire)\\ MAP Sensor Connector 80B - Pin A - Sensor Ground (B/W Wire)\\ VSS - Vehicle Speed Sensor Connector 65B - Pin 1 - 5v Sensor Power (R/W to RED Wire)\\ VSS - Vehicle Speed Sensor Connector 65B - Pin 3 - Uses Powertrain Ground (BLACK Wire) | | | **2004-2006 Engine Control Module**\\ \\ ICM Connector Pin 3 is +5v Output (RED/White Wire)\\ ICM Connector Pin 4 is Sensor Ground (BLACK/White Wire) | MAP Sensor Connector 80B - Pin C - 5v Sensor Power (R/W Wire)\\ MAP Sensor Connector 80B - Pin A - Sensor Ground (B/W Wire)\\ VSS - Vehicle Speed Sensor Connector 65B - Pin 1 - 5v Sensor Power (R/W to RED Wire)\\ VSS - Vehicle Speed Sensor Connector 65B - Pin 3 - Uses Powertrain Ground (BLACK Wire) | | ||
| **2007-2013 Engine Control Module**\\ \\ ECM Connector Pin 14 is +5v Output (RED/White Wire)\\ ECM Connector Pin 26 is Sensor Ground (BLACK/White Wire) | **5v power is fed from ECM Pin 14 to all of these connections:**\\ VSS Connector 65B - Pin A (BLACK/Red Wire)\\ -- (VSS uses Powertrain Ground Point (BLACK Wire)- Not 5v Sensor Ground)\\ (2008-later)Jiffy Stand Connector 133B - Pin 1 (R/W Wire)\\ -- (JSS uses Powertrain Ground (BLACK Wire))\\ ---- (This connector on all models may have an issue due to its location)\\ Passes Thru Engine Harness Connector 145A/B - Pin 5 (R/W Wire)\\ TMAP Sensor Connector 80B - Pin C (or 3) (R/W Wire)\\ TPS Sensor Connector 88B - Pin B (R/W Wire)\\ \\ **The following devices are grounded thru the ECM on Pin 26:**\\ ETS - Engine Temp Sensor - Pin 2 (B/W Wire)\\ Front O2S - Oxygen Sensor - Pin 2 - (B/W Wire)\\ Rear O2S - Oxygen Sensor - Pin 2 - (B/W Wire)\\ Passes Thru Engine Harness Connector 145A/B - Pin 3 (B/W Wire)\\ TMAP - Temp/Manifold Abs Pressure Sensor - Pin A (or 1) - (B/W Wire)\\ TPS - Throttle Position Sensor - Pin A - (B/W Wire)\\ \\ ECM Connector Pin 10 & 28 are Power Grounds - They go to the Powertrain Ground Point | | | **2007-2013 Engine Control Module**\\ \\ ECM Connector Pin 14 is +5v Output (RED/White Wire)\\ ECM Connector Pin 26 is Sensor Ground (BLACK/White Wire) | **5v power is fed from ECM Pin 14 to all of these connections:**\\ VSS Connector 65B - Pin A (BLACK/Red Wire)\\ -- (VSS uses Powertrain Ground Point (BLACK Wire)- Not 5v Sensor Ground)\\ (2008-later)Jiffy Stand Connector 133B - Pin 1 (R/W Wire)\\ -- (JSS uses Powertrain Ground (BLACK Wire))\\ ---- (This connector on all models may have an issue due to its location)\\ Passes Thru Engine Harness Connector 145A/B - Pin 5 (R/W Wire)\\ TMAP Sensor Connector 80B - Pin C (or 3) (R/W Wire)\\ TPS Sensor Connector 88B - Pin B (R/W Wire)\\ \\ **The following devices are grounded thru the ECM on Pin 26:**\\ ETS - Engine Temp Sensor - Pin 2 (B/W Wire)\\ Front O2S - Oxygen Sensor - Pin 2 - (B/W Wire)\\ Rear O2S - Oxygen Sensor - Pin 2 - (B/W Wire)\\ Passes Thru Engine Harness Connector 145A/B - Pin 3 (B/W Wire)\\ TMAP - Temp/Manifold Abs Pressure Sensor - Pin A (or 1) - (B/W Wire)\\ TPS - Throttle Position Sensor - Pin A - (B/W Wire)\\ \\ ECM Connector Pin 10 & 28 are Power Grounds - They go to the Powertrain Ground Point | |