Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:evo:elec01 [2020/02/06 00:49] ixl2relax [Grounding is Critical] |
techtalk:evo:elec01 [2020/05/11 00:14] hippysmack [5 Volt Sensor Supply] |
||
---|---|---|---|
Line 132: | Line 132: | ||
Battery condition can be seen as the voltage of the battery after it has been charged. To verify that it is in a 100 percent fully charged condition, charge the battery and disconnect the charger. **Let the battery rest for one to two hours**, then check the voltage level. | Battery condition can be seen as the voltage of the battery after it has been charged. To verify that it is in a 100 percent fully charged condition, charge the battery and disconnect the charger. **Let the battery rest for one to two hours**, then check the voltage level. | ||
- | AGM Batteries ((2016 Sportster Owner's Manual)) | + | {{:techtalk:ref:elec:battery-chargelevel.jpg|}}((2016 Sportster Owner's Manual))((1998 Sportster Service Manual)) |
- | ^ Voltage Reading | 12.7 | 12.6 | 12.3 | 12.0 | 11.8 | | + | |
- | ^ Percent Charged | 100% | 75% | 50% | 25% | 0% | | + | |
- | + | ||
- | Older-style Sealed Lead Acid Batteries ((1998 Sportster Service Manual)) | + | |
- | ^ Voltage Reading | 13.0 | 12.8 | 12.5 | 12.2 | 12.0 | | + | |
- | ^ Percent Charged | 100% | 75% | 50% | 25% | 0% | | + | |
Be sure your multimeter BLACK Probe is properly grounded to the Battery Negative Post or to the frame. | Be sure your multimeter BLACK Probe is properly grounded to the Battery Negative Post or to the frame. | ||
Line 271: | Line 265: | ||
| **2014-later CANbus Engine Control Module**\\ \\ ECM Connector 2 - Pin 9 is +5v Output (RED/White Wire)\\ ECM Connector 2 - Pin 7 is 5v Sensor Ground (BLACK/White Wire) | **5v power is fed from ECM Connector 2 - Pin 9 to all of these connections:**\\ VSS Connector 65B - Pin A (R/W Wire)\\ -- (VSS uses Powertrain Ground Point (BK/GN Wire)- Not 5v Sensor Ground)\\ JSS - Jiffy Stand Sensor Connector 133B - Pin 1 (R/W Wire)\\ -- Uses Powertrain Ground (BK/GN Wire)\\ ---- (This connector on all models may have an issue due to its location)\\ Passes Thru Engine Harness Connector 145A/B - Pin 8 (R/W Wire) to:\\ TMAP Sensor Connector 80B - Pin 3 (R/W Wire)\\ TPS Sensor Connector 88B - (2014 its on Pin 1 (later years its on Pin B)(R/W Wire))\\ \\ **The following devices are grounded thru the ECM on Connector 2 - Pin 7:**\\ ETS - Engine Temp Sensor - Pin B (B/W to TAN Wire)\\ Front O2S - Oxygen Sensor - (138A/B)Pin 4 - (B/W to BLACK Wire)\\ Rear O2S - Oxygen Sensor - (137A/B)Pin 4 - (B/W to BLACK Wire)\\ Passes Thru Engine Harness Connector 145A/B - Pin 6 (B/W Wire)\\ TMAP - Temp/Manifold Abs Pressure Sensor - Pin 1 - (B/W Wire)\\ TPS - Throttle Position Sensor - (2014 its on Pin 2 (later years its on Pin A) (B/W Wire))\\ \\ ECM Connector 1 & Connector 2 - Pin 10 are both listed as Sensor Grounds (BK/GN)\\ ---- These are General Grounds - They go to the Powertrain Ground Point | | | **2014-later CANbus Engine Control Module**\\ \\ ECM Connector 2 - Pin 9 is +5v Output (RED/White Wire)\\ ECM Connector 2 - Pin 7 is 5v Sensor Ground (BLACK/White Wire) | **5v power is fed from ECM Connector 2 - Pin 9 to all of these connections:**\\ VSS Connector 65B - Pin A (R/W Wire)\\ -- (VSS uses Powertrain Ground Point (BK/GN Wire)- Not 5v Sensor Ground)\\ JSS - Jiffy Stand Sensor Connector 133B - Pin 1 (R/W Wire)\\ -- Uses Powertrain Ground (BK/GN Wire)\\ ---- (This connector on all models may have an issue due to its location)\\ Passes Thru Engine Harness Connector 145A/B - Pin 8 (R/W Wire) to:\\ TMAP Sensor Connector 80B - Pin 3 (R/W Wire)\\ TPS Sensor Connector 88B - (2014 its on Pin 1 (later years its on Pin B)(R/W Wire))\\ \\ **The following devices are grounded thru the ECM on Connector 2 - Pin 7:**\\ ETS - Engine Temp Sensor - Pin B (B/W to TAN Wire)\\ Front O2S - Oxygen Sensor - (138A/B)Pin 4 - (B/W to BLACK Wire)\\ Rear O2S - Oxygen Sensor - (137A/B)Pin 4 - (B/W to BLACK Wire)\\ Passes Thru Engine Harness Connector 145A/B - Pin 6 (B/W Wire)\\ TMAP - Temp/Manifold Abs Pressure Sensor - Pin 1 - (B/W Wire)\\ TPS - Throttle Position Sensor - (2014 its on Pin 2 (later years its on Pin A) (B/W Wire))\\ \\ ECM Connector 1 & Connector 2 - Pin 10 are both listed as Sensor Grounds (BK/GN)\\ ---- These are General Grounds - They go to the Powertrain Ground Point | | ||
+ | ====== Tip For Hunting Down Short Circuits ====== | ||
+ | If you are attempting to locate a short circuit, rather than continuing to replace fuses while looking for the | ||
+ | problem, you can use a test light in place of the fuse at the fuse block. ((HD Tech Tip #48 dated August 1998)) Start removing one load at a time or | ||
+ | wiggle wires. When the light goes out, examine the wiring on the portion of circuit last disconnected for the | ||
+ | cause. | ||
\\ | \\ |