Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:evo:elec03g [2021/08/22 05:21] ixl2relax |
techtalk:evo:elec03g [2021/08/22 05:31] ixl2relax [For 2014 - 2021 Models] |
||
---|---|---|---|
Line 5: | Line 5: | ||
==== For 1991 - 2013 Models ==== | ==== For 1991 - 2013 Models ==== | ||
- | Disconnect the Turn Signal Module from the wiring harness connector. Testing will be done on that wiring harness connector. | + | Disconnect the Turn Signal Module from the wiring harness connector. Testing will be done on that wiring harness connector.\\ |
+ | For 1991-2003, the module is under the seat. For 2004-2013, the battery must be removed to withdraw the module located under the battery. | ||
Look at the [[techtalk:evo:elec03#turn_signal_modules|wiring diagram]] for your module. Identify the FEED OUT & SWITCH IN pin numbers as shown on the diagram. | Look at the [[techtalk:evo:elec03#turn_signal_modules|wiring diagram]] for your module. Identify the FEED OUT & SWITCH IN pin numbers as shown on the diagram. | ||
- | Identify the two wires (BROWN wire for RIGHT-side & VIOLET wire for LEFT-side) that should feed power to the lights. Find the two wires (WHITE/BROWN wire for RIGHT-side & WHITE/VIOLET wire for LEFT-side) that are incoming from the handlebar switches. | + | Identify the two wires (BROWN wire for RIGHT-side & VIOLET wire for LEFT-side) that feed power to the lights. Find the two wires (WHITE/BROWN wire for RIGHT-side & WHITE/VIOLET wire for LEFT-side) that are incoming from the handlebar switches. |
- | Now find the connector pin with incoming power - Usually is Pin2, using ORANGE wire or ORANGE/White or GREY wire. | + | The connector pin with incoming power is Pin2, Accessory Power, using an ORANGE wire or ORANGE/White or GREY wire. |
**BEING VERY CAREFUL** not to short any other pins:\\ | **BEING VERY CAREFUL** not to short any other pins:\\ | ||
Line 34: | Line 35: | ||
Disconnect the Body Control Module (BCM) from the wiring harness connector. Testing will be done on that wiring harness connector. | Disconnect the Body Control Module (BCM) from the wiring harness connector. Testing will be done on that wiring harness connector. | ||
+ | Look at the [[techtalk:evo:elec03#turn_signal_modules|BCM wiring diagram]].\\ | ||
All the BCMs use the following pins for power to the TS lights:\\ | All the BCMs use the following pins for power to the TS lights:\\ | ||
Front Right - PinJ2 - BLUE/Orange wire\\ | Front Right - PinJ2 - BLUE/Orange wire\\ | ||
- | Front Left -- PinJ4 - BLUE/Pink wire\\ | + | Front Left --- PinJ4 - BLUE/Pink wire\\ |
Rear Right -- PinK2 - BLUE/Brown wire\\ | Rear Right -- PinK2 - BLUE/Brown wire\\ | ||
Rear Left --- PinK4 - BLUE/Violet wire\\ | Rear Left --- PinK4 - BLUE/Violet wire\\ | ||
- | Pin1 has constant BATTERY POWER - **BE VERY CAREFUL HERE!** This power is fused thru the Main Fuse which will allow **40amps** of power to flow before blowing. **BE VERY CAREFUL** not to short this pin to ground! | + | Pin1 has constant BATTERY POWER - __**BE VERY CAREFUL HERE!**__ This power is fused thru the Main Fuse which will allow **40amps** of power to flow before blowing. **BE VERY CAREFUL** not to short this pin to ground! |
With the TS module disconnected and the __KEYSWITCH OFF__, CAREFULLY put a jumper __BRIEFLY__ between Pin1 (Power into the module) and one of the above identified pins. As power is applied to each pin, the identified TS light should be lit. | With the TS module disconnected and the __KEYSWITCH OFF__, CAREFULLY put a jumper __BRIEFLY__ between Pin1 (Power into the module) and one of the above identified pins. As power is applied to each pin, the identified TS light should be lit. |