This is an old revision of the document!


EVO: Electrical System

The REFERENCE section has a listing of - Device Connector Pinouts:


SDB - Serial Data Bus

In 2004, HD implemented the serial data bus (SDB) on all Sportster models. This single wire, digital communications link, provides a means for the Ignition Control Module (ICM), the Turn Signal Module (TSM/TSSM) and Speedometer/Tachometer to intelligently communicate with one another. There is a 4-pin 'port' connector (called a serial data link) to allow external computer connection to the SDB. It is located near the MaxiFuse.

The SDB link allowed the ICM to be reprogrammable because it allowed the factory and the dealer the ability to use one ICM and program it for either 883 engines or 1200 engines. There are updates that can be dealer 'flashed' into the ICM when new parameters will resolve known problems.

The ICM, TSM & Speedo/Tach regularly communicate their current status to one another. When all operating parameters on the serial data line are within specifications, a state of health message is sent between the components.

The SDB is designed upon a standard SAE serial communication protocol callded “J1850”. The digital data is transmitted and received on a single wire at around 10.4 Kbps. This protocol was used thru the 2013 model year.

Diagnostic Troubleshooting Codes (DTC) are available to be read on the speedometer. A DTC of U1016 indicates that the ECM is not capable of sending this state of health message. A DTC of U1255 indicates that no messages were present during power up of the current key cycle. A DTC of U1016 indicates that there was communication on the data bus since power up, but communication was lost or interrupted during that key cycle.

While it is possible for more than one fault to occur and set more than one DTC, there are several conditions which may result in one fault setting multiple DTCs. For example, serial data DTCs (DTC U1016, U1064, U1097, U1255, U1300 and U1301) may be accompanied by other DTCs. Always correct the serial data DTCs before resolving other DTCs.

Checking SDB Link:
With ignition key switch turned ON, engine not running, transmit data should typically create a voltage on the SDB line (LtGreen/Violet Wire) of 0.6-0.8 volts. The range of voltages that might be seen as acceptable during operation is 0v - 7.0 volts.


Writing about this subject could fill many pages - but it is recommended that you purchase (along with a factory service manual) the Sportster Electrical Diagnostic Manual (EDM) for your specific model year if you intend to service your own bike. It is extremely helpful in understanding the electrical intricacies of your bike. The part number for the EDM is 99495-xx, where xx is your model year.


CANbus - Controller Area Network Bus

In 2014, HD implemented the Controller Area Network bus (CANbus), sometimes referred to as the HDLAN bus, on all Sportster models. This system uses a two wire, digital communications link, providing a means for the Engine Control Module (ECM), the Body Control Module (BCM), the Speedometer/Tachometer, the right & left handlebar control switches and the Anti-lock Brake System (ABS) to intelligently communicate with one another. There is a 6-pin 'port' connector (called a serial data link) to allow external computer connection to the CANbus. It is located near the MaxiFuse.

The CANbus link allows the ECM/BCM to be reprogrammable for different models and for either 883 engines or 1200 engines. There are updates that can be dealer 'flashed' into the ECM/BCM when new parameters will resolve known problems.

The CANbus components regularly communicate their current status to one another. When all operating parameters on the data line are within specifications, a state of health message is sent between the components.

The CANbus is designed upon a standard SAE serial communication protocol. The digital data is transmitted and received using a differential signal on two wires at around 500Kbps.

The voltage on the CANbus wires operates differentially. Both the CAN High (White/Red Wire) and the CAN Low (White/Black Wire) signal lines use a base voltage of 2.5v. When communicating, both lines change their voltage - the High goes to 3.75v (or more) and the Low goes to 1.25v (or less) - in order to create a differential voltage of at least 2.5v. This creates the binary ones and zeros for digital communications.


Writing about this subject could fill many pages - but it is recommended that you purchase (along with a factory service manual) the Sportster Electrical Diagnostic Manual (EDM) for your specific model year if you intend to service your own bike. It is extremely helpful in understanding the electrical intricacies of your bike. The part number for the EDM is 99495-xx, where xx is your model year.


This website uses cookies for visitor traffic analysis. By using the website, you agree with storing the cookies on your computer.More information