Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:engmech01 [2019/11/27 22:00] hippysmack [Cam Cover Seal (86-03)] |
techtalk:evo:engmech01 [2020/02/22 23:13] hippysmack [Shifter shaft Seal] |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| ====== Motor Mounts ====== | ====== Motor Mounts ====== | ||
| - | [[techtalk:evo:susp05|Click here for Engine Mounts]] in the Evo Suspension section of the Sportsterpedia. \\ | + | [[techtalk:evo:engmech09|Click here for Engine Mounts]] in the Evo Suspension section of the Sportsterpedia. \\ |
| ====== Cylinder Mounting Studs ====== | ====== Cylinder Mounting Studs ====== | ||
| Line 18: | Line 18: | ||
| * [[techtalk:evo:engmech01f|Removing, Inspecting and Installing the Cam Cover]] | * [[techtalk:evo:engmech01f|Removing, Inspecting and Installing the Cam Cover]] | ||
| - | ===== #2 Cam Cover Seal (86-03) ===== | + | ===== #2 Cam - Cover Seal (86-03) ===== |
| Seal number (11124): \\ | Seal number (11124): \\ | ||
| This surrounds and seals #2 cam when the cover is installed. \\ | This surrounds and seals #2 cam when the cover is installed. \\ | ||
| See also [[techtalk:evo:engmech01f#cam_cover_seal_86-03|Removal / Installation of the #2 cam cover seal]] in the Sportsterpedia. \\ | See also [[techtalk:evo:engmech01f#cam_cover_seal_86-03|Removal / Installation of the #2 cam cover seal]] in the Sportsterpedia. \\ | ||
| + | | This side faces out. ((photo by Hippysmack)) | This side faces #2 cam shaft. ((photo by Hippysmack)) | | ||
| |{{:techtalk:evo:engmech:11124_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:11124_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:11124_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:11124_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}| | ||
| Line 31: | Line 32: | ||
| * [[techtalk:evo:engmech01k|Removing 91-03 Primary Cover]] | * [[techtalk:evo:engmech01k|Removing 91-03 Primary Cover]] | ||
| + | ==== Shifter shaft Seal ==== | ||
| + | This is a shifter shaft seal on a 1998 1200S primary cover. \\ | ||
| + | {{:techtalk:evo:engmech:98_shifter_shaft_seal_1_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | {{:techtalk:evo:engmech:98_shifter_shaft_seal_2_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_3_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_4_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | {{:techtalk:evo:engmech:98_shifter_shaft_seal_5_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_6_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_7_by_hippysmack.jpg?direct&300|}} \\ | ||
| ====== Engine Case / Sump Drain Plugs ====== | ====== Engine Case / Sump Drain Plugs ====== | ||
| |{{:techtalk:evo:engmech:sump_drain-plug_on_04_by_bored_now.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:sump_drain-plug_on_04_by_bored_now.jpg?direct&300|}}| | ||
| Line 141: | Line 148: | ||
| {{:techtalk:evo:engmech:removing_the_pinion_gear_by_grind.jpg?direct&300|}} ((photo by ~Grind~' of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:evo:engmech:pinion_key_nub_by_aswracing.jpg?direct&250|}} ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666277)) | {{:techtalk:evo:engmech:removing_the_pinion_gear_by_grind.jpg?direct&300|}} ((photo by ~Grind~' of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:evo:engmech:pinion_key_nub_by_aswracing.jpg?direct&250|}} ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666277)) | ||
| - | ===== Pinion Gear Runout ===== | + | ===== Pinion Shaft Runout ===== |
| |Attach a scrap piece of metal to the outside of the gearcase and position a gauge holder on it so it won't move while turning over the engine. ((photos by anachris of the XLFORUM ))||| | |Attach a scrap piece of metal to the outside of the gearcase and position a gauge holder on it so it won't move while turning over the engine. ((photos by anachris of the XLFORUM ))||| | ||
| |{{:techtalk:ref:tools:checking_pinion_shaft_runout_1_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_2_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_3_by_anachris.jpg?direct&300|}}| | |{{:techtalk:ref:tools:checking_pinion_shaft_runout_1_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_2_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_3_by_anachris.jpg?direct&300|}}| | ||
