Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:engmech01 [2019/11/27 22:07] hippysmack [#2 Cam Cover Seal (86-03)] |
techtalk:evo:engmech01 [2020/04/07 18:21] hippysmack [Pinion Shaft Runout] |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| ====== Motor Mounts ====== | ====== Motor Mounts ====== | ||
| - | [[techtalk:evo:susp05|Click here for Engine Mounts]] in the Evo Suspension section of the Sportsterpedia. \\ | + | [[techtalk:evo:engmech09|Click here for Engine Mounts]] in the Evo Suspension section of the Sportsterpedia. \\ |
| ====== Cylinder Mounting Studs ====== | ====== Cylinder Mounting Studs ====== | ||
| Line 32: | Line 32: | ||
| * [[techtalk:evo:engmech01k|Removing 91-03 Primary Cover]] | * [[techtalk:evo:engmech01k|Removing 91-03 Primary Cover]] | ||
| + | ===== Shifter shaft Seal ===== | ||
| + | This is a shifter shaft seal on a 1998 1200S primary cover. \\ | ||
| + | {{:techtalk:evo:engmech:98_shifter_shaft_seal_1_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | {{:techtalk:evo:engmech:98_shifter_shaft_seal_2_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_3_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_4_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | {{:techtalk:evo:engmech:98_shifter_shaft_seal_5_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_6_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:engmech:98_shifter_shaft_seal_7_by_hippysmack.jpg?direct&300|}} \\ | ||
| ====== Engine Case / Sump Drain Plugs ====== | ====== Engine Case / Sump Drain Plugs ====== | ||
| |{{:techtalk:evo:engmech:sump_drain-plug_on_04_by_bored_now.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:sump_drain-plug_on_04_by_bored_now.jpg?direct&300|}}| | ||
| Line 142: | Line 148: | ||
| {{:techtalk:evo:engmech:removing_the_pinion_gear_by_grind.jpg?direct&300|}} ((photo by ~Grind~' of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:evo:engmech:pinion_key_nub_by_aswracing.jpg?direct&250|}} ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666277)) | {{:techtalk:evo:engmech:removing_the_pinion_gear_by_grind.jpg?direct&300|}} ((photo by ~Grind~' of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:evo:engmech:pinion_key_nub_by_aswracing.jpg?direct&250|}} ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666277)) | ||
| - | ===== Pinion Gear Runout ===== | + | ===== Pinion Shaft Runout ===== |
| |Attach a scrap piece of metal to the outside of the gearcase and position a gauge holder on it so it won't move while turning over the engine. ((photos by anachris of the XLFORUM ))||| | |Attach a scrap piece of metal to the outside of the gearcase and position a gauge holder on it so it won't move while turning over the engine. ((photos by anachris of the XLFORUM ))||| | ||
| |{{:techtalk:ref:tools:checking_pinion_shaft_runout_1_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_2_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_3_by_anachris.jpg?direct&300|}}| | |{{:techtalk:ref:tools:checking_pinion_shaft_runout_1_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_2_by_anachris.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_runout_3_by_anachris.jpg?direct&300|}}| | ||
| Line 154: | Line 160: | ||
| |{{:techtalk:ref:tools:checking_pinion_shaft_run-out_1_by_dirtycory.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_run-out_2_by_dirtycory.jpg?direct&300|}}| | |{{:techtalk:ref:tools:checking_pinion_shaft_run-out_1_by_dirtycory.jpg?direct&300|}}|{{:techtalk:ref:tools:checking_pinion_shaft_run-out_2_by_dirtycory.jpg?direct&300|}}| | ||
| + | ====== Crankshaft Seal ====== | ||
| + | Here is a trick to hold the spring in place to stop it popping off while you are fitting the seal. ((DEEP DIVER of the XLFORUM http://xlforum.net/forums/showthread.php?p=5489312&highlight=main+seal#post5489312)) \\ | ||
| + | Before fitting it, pack some grease around the spring in the seal groove. You only need a small amount. \\ | ||
