Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:engmech01f [2019/11/27 22:07] hippysmack [Cam Cover Seal (86-03)] |
techtalk:evo:engmech01f [2019/11/27 22:16] hippysmack [Installation] |
||
|---|---|---|---|
| Line 73: | Line 73: | ||
| ====== Gaskets / Seals ====== | ====== Gaskets / Seals ====== | ||
| - | ===== #2 Cam - Cover Seal (86-03) ===== | ||
| - | Seal number (11124): \\ | ||
| - | This surrounds and seals #2 cam when the cover is installed. \\ | ||
| - | |||
| - | | This side faces out. ((photo by Hippysmack)) | This side faces #2 cam shaft. ((photo by Hippysmack)) | | ||
| - | |{{:techtalk:evo:engmech:11124_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:11124_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | Check the #2 cam seal for damage. It's always best to go ahead and replace it while you have the cover off. \\ | ||
| - | |||
| - | Using a screwdriver and hammer, insert the screwdriver inside the lip of the seal from the rear of the cover. \\ | ||
| - | Knock the seal out of the cover. ((photos by Hippysmack)) \\ | ||
| - | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | Clean the recessed area for the new seal thoroughly. \\ | ||
| - | You can use compressed air or brake cleaner (cover the ignition if still installed). | ||
| - | Set the new seal over the hole aligning it as straight as possible. ((photos by Hippysmack)) \\ | ||
| - | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_4_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | Use a socket and a hammer to drive in the new seal straight to the cover. \\ | ||
| - | The socket O.D. needs to be just smaller than the seal. \\ | ||
| - | Make sure the seal is flush to the cover when done. ((photos by Hippysmack)) \\ | ||
| - | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_7_by_hippysmack.jpg?direct&300|}}| | ||
| ====== Installation ====== | ====== Installation ====== | ||
| Line 122: | Line 100: | ||
| |{{:techtalk:evo:engmech:cam_cover_installation_by_cjburr.jpg?direct&300|}}|{{:techtalk:evo:engmech:98_gearcase_cover_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:cam_cover_installation_by_cjburr.jpg?direct&300|}}|{{:techtalk:evo:engmech:98_gearcase_cover_by_hippysmack.jpg?direct&300|}}| | ||
| + | ===== #2 Cam - Cover Seal (86-03) ===== | ||
| + | Seal number (11124): \\ | ||
| + | This surrounds and seals #2 cam when the cover is installed. \\ | ||
| + | |||
| + | | This side faces out. ((photo by Hippysmack)) | This side faces #2 cam shaft. ((photo by Hippysmack)) | | ||
| + | |{{:techtalk:evo:engmech:11124_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:11124_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| + | Check the #2 cam seal for damage. It's always best to go ahead and replace it while you have the cover off. \\ | ||
| + | |||
| + | Using a screwdriver and hammer, insert the screwdriver inside the lip of the seal from the rear of the cover. \\ | ||
| + | Knock the seal out of the cover. ((photos by Hippysmack)) \\ | ||
| + | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| + | Clean the recessed area for the new seal thoroughly. \\ | ||
| + | You can use compressed air or brake cleaner (cover the ignition if still installed). | ||
| + | Set the new seal over the hole aligning it as straight as possible. ((photos by Hippysmack)) \\ | ||
| + | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_4_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| + | Use a socket and a hammer to drive in the new seal straight to the cover. \\ | ||
| + | The socket O.D. needs to be just smaller than the seal. \\ | ||
| + | Make sure the seal is flush to the cover when done. ((photos by Hippysmack)) \\ | ||
| + | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_7_by_hippysmack.jpg?direct&300|}}| | ||
