Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Next revision Both sides next revision | ||
techtalk:evo:engmech01f [2019/11/27 22:16] hippysmack [#2 Cam - Cover Seal (86-03)] |
techtalk:evo:engmech01f [2019/11/27 22:16] hippysmack [Installation] |
||
---|---|---|---|
Line 100: | Line 100: | ||
|{{:techtalk:evo:engmech:cam_cover_installation_by_cjburr.jpg?direct&300|}}|{{:techtalk:evo:engmech:98_gearcase_cover_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:cam_cover_installation_by_cjburr.jpg?direct&300|}}|{{:techtalk:evo:engmech:98_gearcase_cover_by_hippysmack.jpg?direct&300|}}| | ||
+ | ===== #2 Cam - Cover Seal (86-03) ===== | ||
+ | Seal number (11124): \\ | ||
+ | This surrounds and seals #2 cam when the cover is installed. \\ | ||
+ | |||
+ | | This side faces out. ((photo by Hippysmack)) | This side faces #2 cam shaft. ((photo by Hippysmack)) | | ||
+ | |{{:techtalk:evo:engmech:11124_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:11124_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | Check the #2 cam seal for damage. It's always best to go ahead and replace it while you have the cover off. \\ | ||
+ | |||
+ | Using a screwdriver and hammer, insert the screwdriver inside the lip of the seal from the rear of the cover. \\ | ||
+ | Knock the seal out of the cover. ((photos by Hippysmack)) \\ | ||
+ | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_2_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | Clean the recessed area for the new seal thoroughly. \\ | ||
+ | You can use compressed air or brake cleaner (cover the ignition if still installed). | ||
+ | Set the new seal over the hole aligning it as straight as possible. ((photos by Hippysmack)) \\ | ||
+ | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_4_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | Use a socket and a hammer to drive in the new seal straight to the cover. \\ | ||
+ | The socket O.D. needs to be just smaller than the seal. \\ | ||
+ | Make sure the seal is flush to the cover when done. ((photos by Hippysmack)) \\ | ||
+ | |{{:techtalk:evo:engmech:replacing_cam_cover_seal_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:replacing_cam_cover_seal_7_by_hippysmack.jpg?direct&300|}}| | ||