Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:engmech01k [2019/11/12 06:40] hippysmack [Remove clutch adjustment assembly] |
techtalk:evo:engmech01k [2019/11/12 17:25] hippysmack [Loosen the primary chain adjuster] |
||
|---|---|---|---|
| Line 49: | Line 49: | ||
| ===== Remove the clutch ramp assembly ===== | ===== Remove the clutch ramp assembly ===== | ||
| - | Remove the derby cover and the clutch ramp assembly to gain access to the clutch basket mounting nut. \\ | + | Remove the derby cover and the clutch ramp assembly. \\ |
| {{:techtalk:evo:priclutch:adjusting_clutch_1_by_hippysmack.jpg?direct&300|}} \\ | {{:techtalk:evo:priclutch:adjusting_clutch_1_by_hippysmack.jpg?direct&300|}} \\ | ||
| Line 59: | Line 59: | ||
| {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| - | ===== Remove clutch adjustment assembly ===== | + | ===== Loosen the primary chain adjuster ===== |
| - | Use circlips pliers to remove the circlip and the adjuster assembly simply falls out of the clutch hub. \\ | + | Hold the stud with a 1/4" Allen wrench and use a 7/8" open end wrench to loosen the tightening nut. \\ |
| - | Inspect the bearings / race for smooth operation and / or damage. The circlip is reusable as long as it's not bent / warped. \\ | + | Once the nut is loose, unscrew the stud until it bottoms out to loosen the chain adjuster. \ |
| - | {{:techtalk:evo:priclutch:removing_clutch_adjustment-bearing_assembly_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_adjustment-bearing_assembly_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | + | This is easier done before removing the cover since the engine holds the assembly in place. \\ |
| + | If you don't loosen this before re-installing the cover, it will be more difficult to install the cover later. \\ | ||
| + | |||
| + | {{:techtalk:evo:engmech:removing_primary_cover_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| ===== Loosen and remove the primary cover ===== | ===== Loosen and remove the primary cover ===== | ||
