Differences

This shows you the differences between two versions of the page.

--- techtalk:evo:engmech01k [2019/11/12 04:22]
hippysmack
+++ techtalk:evo:engmech01k [2024/01/03 17:15] (current)
hippysmack [Loosen and remove the primary cover]
@@ Line 2: / Line 2: @@
 ====== EVO: Engine Mechanicals - Sub-01K ======
 \\
-====== Removing the Primary Cover ======
+====== Removing 91-03 Primary Cover ======
 Before removing the primary cover, you'll need to remove the shift lever bracket (or mid foot pedal bracket if applicable), linkage and derby cover. \\
 Drain the primary fluid, loosen or remove the clutch cable and loosen the primary chain adjuster. \\
-====== Before removing the primary cover ======
-Remove shift lever. \\
+===== Remove shift lever =====
 {{:techtalk:evo:engmech:removing_primary_cover_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
@@ Line 15: / Line 15: @@
 {{:techtalk:evo:engmech:removing_primary_cover_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
+===== Clutch cable =====
 The clutch cable is best removed from the cover. \\
@@ Line 21: / Line 23: @@
 If you have to remove the cable connection or the cover completely from the engine, removing the cable is the easy part. \\
 It's easy to cross thread the cable in the primary cover if the cable isn't stretched out to keep it from binding up when installing. \\
-To remove the clutch cable, detach both ends as shown below and any holding clips and/or wire ties
+To remove the clutch cable, detach both ends as shown below and any holding clips and / or wire ties. \\
+Retract the cable connection fully to allow slack on the inner braided wire. \\
 {{:techtalk:evo:priclutch:adjusting_-_removing_clutch_cable_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:adjusting_-_removing_clutch_cable_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:adjusting_-_removing_clutch_cable_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
 {{:techtalk:evo:priclutch:adjusting_-_removing_clutch_cable_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:adjusting_-_removing_clutch_cable_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:adjusting_-_removing_clutch_cable_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
-Remove the derby cover and the clutch ramp assembly to gain access to the clutch basket mounting nut. \\
+Remove the cable holding clip (if used) and any wire ties etc. that may be holding the cable to the frame. \\
+{{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
+Remove the clutch lever from it's bracket by removing the retaining ring (circlip) underneath and pivot pin from the top. \\
+Then pull the lever from the bracket, swing the cable wire through the slot in the bracket and remove the plastic cable pin. \\
+{{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_8_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_9_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_10_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
+Then pull the clutch cable down thru the trees and lay it out in front of the bike. \\
+Use a 1/2" open end wrench to loosen the cable connector at the primary cover and then you can most likely twist the cable to loosen the threads. \\
+This method will help keep the cable straight so as to not cross thread it making it more safe for re-installing the cable later. \\
+Be careful not to damage the O-ring on the part of the cable that comes out of the cover. \\
+Inspect the O-ring and replace it if needed. \\
+{{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_12_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:adjusting_-_removing_clutch_cable_13_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
+===== Remove the clutch ramp assembly =====
+Remove the derby cover and the clutch ramp assembly. \\
 {{:techtalk:evo:priclutch:adjusting_clutch_1_by_hippysmack.jpg?direct&300|}} \\
@@ Line 37: / Line 59: @@
 {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:priclutch:removing_clutch_ramp_assembly_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
+===== Loosen the primary chain adjuster =====
+Loosening the primary chain adjuster takes the pressure off the primary chain from the cover. \\
+Hold the stud with a 1/4" Allen wrench and use a 7/8" open end wrench to loosen the tightening nut. \\
+Once the nut is loose, unscrew the stud until it bottoms out to loosen the chain adjuster. \
+This is easier done before removing the cover since the engine holds the assembly in place. \\
+If you don't loosen this before re-installing the cover, it will be more difficult to install the cover later. \\
+{{:techtalk:evo:engmech:removing_primary_cover_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
+===== Loosen and remove the primary cover =====
+Loosen the screws will most likely result in an oil leak. So, first, put an oil drain bucket or catch pan under the engine. \\
+Loosen the primary cover screws but don't completely remove them to allow oil to drain into a bucket or catch pan. \\
-Loosen the primary cover screws to allow oil to drain in a bucket / catch pan. \\
+The primary cover has (14) 1/4" and (2) 5/16" Allen head screws of various lengths. \\
-Some of the screws are different lengths and need to be placed back in their respective places. \\
+They will need to be replaced back in the same holes from which they were removed. \\
-You can use a piece of cardboard with a sketch drawn of the cover as to where the bolts go. \\
+So, their proper location will need to be marked upon removal. You can make a drawing of the primary cover on a piece of cardboard. \\
+Then put them into the cardboard in the proper orientation as removed from the cover. \\
 You can punch the holes with a screwdriver, insert the screws for holding and it makes reassembly less of a headache. \\
-{{:techtalk:evo:elec:replacing_the_stator_on_91-03_pic_1_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM http://xlforum.net/forums/showthread.php?t=1823130)) {{:techtalk:ref:tools:primary_cover_screw_holder_by_cjburr.jpg?direct&300|}} ((photo by cjburr of the XLFORUM http://xlforum.net/forums/showthread.php?t=49915)) \\
+{{:techtalk:evo:engmech:removing_primary_cover_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_8_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:primary_cover_screw_holder_by_cjburr.jpg?direct&300|}} ((photo by cjburr of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-drivetrain/sportster-motorcycle-transmission-clutch-primary-secondary-drive/29955-06-clutch-install?t=49915)) \\
-Loosening the primary chain adjuster takes the pressure off the primary chain from the cover. \\
+{{:techtalk:evo:engmech:removing_primary_cover_9_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_11_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:removing_primary_cover_10_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
 \\

Trace:

Differences

Navigation

Search

Toolbox