Differences

This shows you the differences between two versions of the page.

--- techtalk:evo:engmech02 [2019/02/22 01:48]
hippysmack [00-05 Lifter Ant-Rotation Screws]
+++ techtalk:evo:engmech02 [2019/08/11 03:28]
ixl2relax [Comparing OEM and Andrews Cam Grinds]
@@ Line 3: / Line 3: @@
 ====== Camshafts ======
-===== Cam Specs =====
+===== Cam Specs - OEM & SE =====
 {{:techtalk:evo:engmech:camspecs-d-w-se-chart.jpg|400}}
@@ Line 15: / Line 15: @@
 |C ((MMI Evolution Cam Specs dated 10/5/92))|.278"|1°ATDC|42° ABDC|225°|.280"|42° BBDC|3° ATDC|225°|4°|
-==== Comparing Andrews and OEM Cam Grinds ====
+==== Comparing OEM and Andrews Cam Grinds ====
-These figures are from the Sportster Evolution Cams PDF from Andrews Products.
+These figures are from the Sportster Evolution Cams PDF from Andrews Products. ((Page25 - http://www.bigboarv-twin.com/wp-content/uploads/2015/07/Andrews-Products-Catalogue-20141.pdf))
-|Grind|Timing \\ @ .053" Lift|CL|Duration @ \\ .053" Lift|Durarion @ \\ .020" Lift|Max Lift|TDC Lift|
+|Grind|I/E|Timing \\ @ .053" Lift|CL|Duration @ \\ .053" Lift|Durarion @ \\ .020" Lift|Max Lift|TDC Lift|
-|W|10°/28°|99°|218°|256°|.474"|.122"|
+|W|I|10°/28°|99°|218°|256°|.474"|.122"|
-|W|38°/16°|101°|234°|272°|.474"|.138"|
+|:::|E|38°/16°|101°|234°|272°|.474"|.138"|
-|N-4|30°/46°|98°|256°|296°|.490"|.216"|
+|N4|I|30°/46°|98°|256°|296°|.490"|.216"|
-|N-4|52°/24°|104°|256°|296°|.490"|.189"|
+|:::|E|52°/24°|104°|256°|296°|.490"|.189"|
+I/E = Intake/Exhaust --- CL = Centerline
+\\
+Thanks to Maxeffort of the XLForum for the following Degree Wheel Charts of these various cams.\\
+Note that the measurements are based on the .053 lift specs.
+{{:techtalk:evo:engmech:camwheel-hdw-218-234-474-maxeffort.jpg?400|}}   {{:techtalk:evo:engmech:camwheel-hdd-223-223-458-maxeffort.jpg?400|}}\\
+{{:techtalk:evo:engmech:camwheel-an4-256-256-490-maxeffort.jpg?400|}}   {{:techtalk:evo:engmech:camwheel-an2-240-244-465-440-maxeffort.jpg?v|}}\\
+{{:techtalk:evo:engmech:camwheel-h560-256-266-560-maxeffort.jpg?400|}}   {{:techtalk:evo:engmech:camwheel-h570-240-250-570-maxeffort.jpg?400|}}\\
+{{:techtalk:evo:engmech:camwheel-rs567-253-253-567-maxeffort.jpg?v|}}   {{:techtalk:evo:engmech:camwheel-rs575-244-244-575-maxeffort.jpg?400|}}
-CL = Centerline
 ===== Removing / Installing Evo Cams =====
 ===== Sub Documents =====
@@ Line 129: / Line 142: @@
 |{{:techtalk:evo:engmech:anti-rotation_pin_hardware_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:anti-rotation_pin_hardware_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:anti-rotation_pin_o-ring_by_hippysmack.jpg?direct&300|}}|
-|  App. dims ((photos by Hippysmack))  ||
+|  App. pin dims ((photos by Hippysmack))  ||
 |{{:techtalk:evo:engmech:91-99_anti-rotation_pins_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_anti-rotation_pins_8_by_hippysmack.jpg?direct&300|}}|
+|  App. pin plate dims ((photos by Hippysmack))  |||
+|{{:techtalk:evo:engmech:91-99_anti-rotation_pins_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_anti-rotation_pins_10_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_anti-rotation_pins_11_by_hippysmack.jpg?direct&300|}}|
 |  Slide the pins in the holes, install the O-rings over the pins. ((photos by Hippysmack))  |||

Trace:

Differences

Navigation

Search

Toolbox