Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:evo:engmech02 [2019/02/14 04:34]
hippysmack [06-Up Anti-Rotation Device]
techtalk:evo:engmech02 [2019/08/11 18:16]
ixl2relax [Comparing OEM and Andrews Cam Grinds]
Line 3: Line 3:
  
 ====== Camshafts ====== ====== Camshafts ======
-===== Cam Specs =====+===== Cam Specs - OEM & SE =====
  
 {{:​techtalk:​evo:​engmech:​camspecs-d-w-se-chart.jpg|400}} {{:​techtalk:​evo:​engmech:​camspecs-d-w-se-chart.jpg|400}}
Line 15: Line 15:
 |C ((MMI Evolution Cam Specs dated 10/​5/​92))|.278"​|1°ATDC|42° ABDC|225°|.280"​|42° BBDC|3° ATDC|225°|4°| |C ((MMI Evolution Cam Specs dated 10/​5/​92))|.278"​|1°ATDC|42° ABDC|225°|.280"​|42° BBDC|3° ATDC|225°|4°|
  
-==== Comparing ​Andrews and OEM Cam Grinds ==== +==== Comparing OEM and Andrews ​Cam Grinds ==== 
-These figures are from the Sportster Evolution Cams PDF from Andrews Products.+These figures are from the Sportster Evolution Cams PDF from Andrews Products. ​((Page25 - http://​www.bigboarv-twin.com/​wp-content/​uploads/​2015/​07/​Andrews-Products-Catalogue-20141.pdf))
  
-|Grind|Timing \\ @ .053" Lift|CL|Duration @ \\ .053" Lift|Durarion @ \\ .020" Lift|Max Lift|TDC Lift| +|Grind|I/E|Timing \\ @ .053" Lift|CL|Duration @ \\ .053" Lift|Durarion @ \\ .020" Lift|Max Lift|TDC Lift| 
-|W|10°/​28°|99°|218°|256°|.474"​|.122"​| +|W|I|10°/​28°|99°|218°|256°|.474"​|.122"​| 
-|W|38°/​16°|101°|234°|272°|.474"​|.138"​| +|:::|E|38°/​16°|101°|234°|272°|.474"​|.138"​| 
-|N-4|30°/​46°|98°|256°|296°|.490"​|.216"​| +|N4|I|30°/​46°|98°|256°|296°|.490"​|.216"​| 
-|N-4|52°/​24°|104°|256°|296°|.490"​|.189"​|+|:::|E|52°/​24°|104°|256°|296°|.490"​|.189"​|
  
  
-CL = Centerline+I/E = Intake/​Exhaust --- CL = Centerline 
 + 
 +\\ 
 + 
 + 
 +Thanks to Maxeffort of the XLForum for the following Flywheel Degree Charts of these various cams.((Maxeffort at this post: http://​xlforum.net/​forums/​showthread.php?​t=2074322)) 
 + 
 +The measurements are based on the .053 lift specs. Also, take note that the predominance of the intake valve opening occurs on one rotation of the flywheel and the predominance of the exhaust valve opening occurs on the next rotation of the flywheel. It takes two full rotations (720°) of the flywheel to complete the four-cycle process. (This view of the flywheel would be from the right side of the engine.) 
 + 
 +\\ 
 + 
 +{{:​techtalk:​evo:​engmech:​camwheel-hdw-218-234-474-maxeffort.jpg?​400|}} ​  ​{{:​techtalk:​evo:​engmech:​camwheel-hdd-223-223-458-maxeffort.jpg?​400|}} 
 + 
 +\\ 
 + 
 +{{:​techtalk:​evo:​engmech:​camwheel-an4-256-256-490-maxeffort.jpg?​400|}} ​  ​{{:​techtalk:​evo:​engmech:​camwheel-an2-240-244-465-440-maxeffort.jpg?​400|}} 
 + 
 +\\ 
 + 
 +{{:​techtalk:​evo:​engmech:​camwheel-h560-256-266-560-maxeffort.jpg?​400|}} ​  ​{{:​techtalk:​evo:​engmech:​camwheel-h570-240-250-570-maxeffort.jpg?​400|}} 
 + 
 +\\ 
 + 
 +{{:​techtalk:​evo:​engmech:​camwheel-rs567-253-253-567-maxeffort.jpg?​400|}} ​  ​{{:​techtalk:​evo:​engmech:​camwheel-rs575-244-244-575-maxeffort.jpg?​400|}} 
 + 
 +\\ 
 ===== Removing / Installing Evo Cams ===== ===== Removing / Installing Evo Cams =====
 ===== Sub Documents ===== ===== Sub Documents =====
Line 79: Line 105:
 ====== Tappets (lifters) ====== ====== Tappets (lifters) ======
 ====== Hydraulic Lifters ====== ====== Hydraulic Lifters ======
 +===== Sub-Documents =====
 +  * [[techtalk:​evo:​engmech02b|91-99 Lifter Pin Upgrade to 00-05 Lifter Pin Screws]]
 +
 +See also in the REF section of the Sportsterpedia:​
 +
 +  * [[techtalk:​ref:​svcproc16|Hydraulic Lifter - Disassembly / Inspection / Assembly]] ​
 +
 There was a running change to new style hydraulic lifters in 1986 for Sportsters. ((1986-1990 HD Sportster FSM pg 3-44)) \\ There was a running change to new style hydraulic lifters in 1986 for Sportsters. ((1986-1990 HD Sportster FSM pg 3-44)) \\
 They were the same as those used in 1340cc engines beginning in the 1986 model year. \\ They were the same as those used in 1340cc engines beginning in the 1986 model year. \\
Line 121: Line 154:
 |  91-99 anti-rotation pin hardware ((photos by Hippysmack)) ​ ||| |  91-99 anti-rotation pin hardware ((photos by Hippysmack)) ​ |||
 |{{:​techtalk:​evo:​engmech:​anti-rotation_pin_hardware_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​anti-rotation_pin_hardware_2_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​anti-rotation_pin_o-ring_by_hippysmack.jpg?​direct&​300|}}| |{{:​techtalk:​evo:​engmech:​anti-rotation_pin_hardware_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​anti-rotation_pin_hardware_2_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​anti-rotation_pin_o-ring_by_hippysmack.jpg?​direct&​300|}}|
 +
 +|  App. pin dims ((photos by Hippysmack)) ​ ||
 +|{{:​techtalk:​evo:​engmech:​91-99_anti-rotation_pins_7_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​91-99_anti-rotation_pins_8_by_hippysmack.jpg?​direct&​300|}}|
 +
 +|  App. pin plate dims ((photos by Hippysmack)) ​ |||
 +|{{:​techtalk:​evo:​engmech:​91-99_anti-rotation_pins_9_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​91-99_anti-rotation_pins_10_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​91-99_anti-rotation_pins_11_by_hippysmack.jpg?​direct&​300|}}|
  
 |  Slide the pins in the holes, install the O-rings over the pins. ((photos by Hippysmack)) ​ ||| |  Slide the pins in the holes, install the O-rings over the pins. ((photos by Hippysmack)) ​ |||
Line 147: Line 186:
  
 **Torque**: 55-65 in. lbs. (6.2-7.3 Nm) ((04 HD Sportster FSM pg 3-7)) \\ **Torque**: 55-65 in. lbs. (6.2-7.3 Nm) ((04 HD Sportster FSM pg 3-7)) \\
-| 00-05 anti-rotation screws ((photo by Hoppysmack)) ​ |  End of screws run up into the case. ((photos by JohnK of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1422877&​page=6)) ​ || + 00-05 anti-rotation screws ((photo by Hoppysmack))  ​|  App dims  (photos by Hippysmack)) ​ || 
-|{{:​techtalk:​evo:​engmech:​00-05_anti-rotation_pins_1_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​oil:​05_tappet_screws_1_by_johnk.jpg?​direct&​300|}}|{{:​techtalk:​evo:​oil:​05_tappet_screws_2_by_johnk.jpg?​direct&​300|}}|+|{{:​techtalk:​evo:​engmech:​00-05_anti-rotation_pins_1_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​00-05_anti-rotation_pins_2_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​00-05_anti-rotation_pins_3_by_hippysmack.jpg?​direct&​300|}}| 
 + 
 +|  End of screws run up into the case. ((photos by JohnK of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1422877&​page=6)) ​ || 
 +|{{:​techtalk:​evo:​oil:​05_tappet_screws_1_by_johnk.jpg?​direct&​300|}}|{{:​techtalk:​evo:​oil:​05_tappet_screws_2_by_johnk.jpg?​direct&​300|}}|
  
 ===== 06-Up Anti-Rotation Device ===== ===== 06-Up Anti-Rotation Device =====
Line 158: Line 200:
  
 These work OK for stock cams. \\ These work OK for stock cams. \\
-But if you're upgrading to bigger cams, anything more than .600 lift has too small a base circle. \\+But if you're upgrading to bigger cams, anything more than .600 lift has too small a base circle. ​((rocketmangb of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​p=5613140&​highlight=anti+rotation#​post5613140)) ​\\
 (and they will nearly drop out of the ARDs and they can also spin away from them) \\ (and they will nearly drop out of the ARDs and they can also spin away from them) \\
 The big issue is that they turn sideways with the roller not turning on the cam lobe. \\ The big issue is that they turn sideways with the roller not turning on the cam lobe. \\
Line 165: Line 207:
 |  ARD block ((photo by rocketmangb of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1768265&​page=31)) ​ |  ARD block installed ((photo by chris_b_owens of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​p=5042968)) ​ |  |  ARD block ((photo by rocketmangb of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1768265&​page=31)) ​ |  ARD block installed ((photo by chris_b_owens of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​p=5042968)) ​ | 
 |{{:​techtalk:​evo:​engmech:​06_ard_by_rocketmangb.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​2013_ard_by_chris_b_owens.jpg?​direct&​300|}}| |{{:​techtalk:​evo:​engmech:​06_ard_by_rocketmangb.jpg?​direct&​300|}}|{{:​techtalk:​evo:​engmech:​2013_ard_by_chris_b_owens.jpg?​direct&​300|}}|
-===== Lifter Anti-Rotation ===== 
-Anti-roll pins / blocks (respectively) are designed to keep roller lifters from turning sideways during operation. \\ 
-A roller that's turned sideways does not roll. ((NRHS Sales of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1768265&​page=29)) \\ 
- 
- 
-{{:​techtalk:​evo:​engmech:​99-00_anti-rotation_pin_comparison_by_hippysmack.jpg?​direct&​300|}} ((photo by Hippysmack)) {{:​techtalk:​evo:​engmech:​99-00_anti-rotation_pin_comparison_2_by_hippysmack.jpg?​direct&​300|}} ((photo by Hippysmack)) 
- 
- 
- 
- 
  
 ====== Pinion Gear ====== ====== Pinion Gear ======