Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:evo:engmech03a [2019/08/01 01:07] hippysmack |
techtalk:evo:engmech03a [2024/01/03 20:54] (current) hippysmack |
||
---|---|---|---|
Line 4: | Line 4: | ||
====== Cylinder / Head Bolt Issues and Repair ====== | ====== Cylinder / Head Bolt Issues and Repair ====== | ||
===== Sub Documents ===== | ===== Sub Documents ===== | ||
- | See also [[techtalk:ref:genmsr36#time-sert_repair_on_engine_case_using_drill_press|Time-Sert repair on engine case using drill press]] in the Sportsterpedia for cylinder / head stud repair. | + | See also in the Sportsterpedia: |
- | + | * [[techtalk:evo:engmech03b|Time-Sert Repair on Engine Case Cylinder / Head Stud Hole]] | |
+ | * [[techtalk:ref:tools023#warped_or_damaged_thread_repair|Warped or Damaged Thread Repair]] | ||
===== Loose Head Bolt Studs ===== | ===== Loose Head Bolt Studs ===== | ||
A big concern about the studs becoming loose is the threads being stripped in the case. \\ | A big concern about the studs becoming loose is the threads being stripped in the case. \\ | ||
The two side by side bolt holes on the right side in the pic below are each drilled into the opposing holes and tapped. \\ | The two side by side bolt holes on the right side in the pic below are each drilled into the opposing holes and tapped. \\ | ||
So each hole is depending, in part, of the strength of the other. \\ | So each hole is depending, in part, of the strength of the other. \\ | ||
- | With the bolts loosening, it is at least suspect that the threads or the hole strength is compromised. ((Hippysmack of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074117&page=2)) \\ | + | With the bolts loosening, it is at least suspect that the threads or the hole strength is compromised. ((Hippysmack of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-motor-top-end/197474-leaking-head-gasket-loose-head-bolts/page2?t=2074117&page=2)) \\ |
- | | Weakest head stud holes in the case. ((photo by Hippysmack)) | | + | | Weakest head stud holes in the case. ((photo by Hippysmack)) | Head bolt pulled out of the case. ((photo by Blue Scoot of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-motor-top-end/198541-repairing-cylinder-studs-cases/page5#post4360678)) | |
- | |{{:techtalk:evo:engmech:weakest_cylinder_bolt_threads_by_hippysmack.jpg?direct&300|}}| | + | |{{:techtalk:evo:engmech:weakest_cylinder_bolt_threads_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:head_bolt_pulled_out_by_blue_scoot.jpg?direct&300|}}| |
There is a procedure in the manual for tightening the studs before installing the cylinders and heads. \\ | There is a procedure in the manual for tightening the studs before installing the cylinders and heads. \\ | ||
Line 25: | Line 25: | ||
If a stud is backing out, it could have simply be from it being installed improperly to begin with. \\ | If a stud is backing out, it could have simply be from it being installed improperly to begin with. \\ | ||
It is possible that the stud turned when the head cap nuts were removed. \\ | It is possible that the stud turned when the head cap nuts were removed. \\ | ||
- | Heat plays a role in what happens to the studs / nuts also and can lock the cap screw tighter than the stud is to the case. | + | Heat plays a role in what happens to the studs / nuts also and can lock the cap screw tighter than the stud is to the case. \\ |
So it is possible that the top nut was just tight to the stud before breaking loose. \\ | So it is possible that the top nut was just tight to the stud before breaking loose. \\ | ||
First try and remove any studs that back out and check the threads in the case as well as the stud. \\ | First try and remove any studs that back out and check the threads in the case as well as the stud. \\ | ||
Line 38: | Line 38: | ||
This will also cause a leak if not done properly. \\ | This will also cause a leak if not done properly. \\ | ||
\\ | \\ | ||
- | ===== Stud Removal ===== | ||
- | |||
- | |||
- | |{{:techtalk:evo:engmech:bent_socket_ext_while_removing_cylinder_stud_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:broken_stud_extractor_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:damaged_cylinder_stud_while_removing_by_hippysmack.jpg?direct&300|}}| | ||
- | The idea below to soak the threads in oil was in response to the broken tool(s) above. \\ | + | ==== Soaking the threads for easier removal ==== |
+ | Soaking the threads is usually advised before attempting to remove them. \\ | ||
Due to the angle of the block, it's not possible to actually leave anything next to the threads since it will simply slide down the block. \\ | Due to the angle of the block, it's not possible to actually leave anything next to the threads since it will simply slide down the block. \\ | ||
So a 'holding chamber' was made to let the oil sit and penetrate the threads. \\ | So a 'holding chamber' was made to let the oil sit and penetrate the threads. \\ | ||
Line 53: | Line 50: | ||
{{:techtalk:evo:engmech:stuck_cylinder_stud_removal_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | {{:techtalk:evo:engmech:stuck_cylinder_stud_removal_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
- | ===== Stripped Case Threads ===== | + | ===== Stud Removal ===== |
+ | ==== Using stud removal tools to loosen the stud ==== | ||
+ | |{{:techtalk:evo:engmech:bent_socket_ext_while_removing_cylinder_stud_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:broken_stud_extractor_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:damaged_cylinder_stud_while_removing_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | ==== Using a pipe wrench to loosen the stud ==== | ||
+ | |||
+ | A propane torch works well to melt or loosen old Loctite (red or blue) on the threads. \\ | ||
+ | |||
+ | Catch the stud down low, but not so low as to run the wrench into the block. \\ | ||
+ | Lay some rags over the bore, find a small piece of plywood even a short 2x4 block, drill a hole in the middle and slide it down the stud. \\ | ||
+ | Then clamp the stud with the pipe wrench on top of the wood. \\ | ||
+ | Set the jaws of the wrench over the stud, adjust then to the stud. \\ | ||
+ | Use one hand to cup over the wrench and stud and the other on the handle. \\ | ||
+ | You'll get more even torque if you can let your body lean into the handle as well. \\ | ||
+ | It may scare you when the stud breaks loose. It'll make a cracking noise which is normal. \\ | ||
+ | The wrench won't turn all the way around due the the other studs in the way. \\ | ||
+ | So you'll have to remove the wrench and get another grip to continue turning until it gets loose enough to turn by hand. \\ | ||
+ | Once you get to where it doesn't take so much torque to turn it, you can use double nuts on the top threads if you prefer. \\ | ||
+ | The pipe wrench is mainly to break torque. It's easier to get out of hand and damage something if it's not needed after that. \\ | ||
+ | |||
+ | If the pipe wrench slips, you may need to adjust the wrench so the stud is closer to the inside teeth. \\ | ||
+ | You may need to loosen the jaws to move the stud back. \\ | ||
+ | The wrench doesn't have to be tight against the stud to grip. \\ | ||
+ | It works by the magic of binding onto the stud. \\ | ||
+ | It's important to hold center on the wrench and stud with one hand. \\ | ||
+ | You can try getting a grip by tilting the handle up with just a little pressure and then back level. \\ | ||
+ | You just have to find a way to make the wrench bind against the stud. \\ | ||
+ | |||
+ | |If the wrench doesn't grip, make it bind on the stud. ((photo by Blue Scoot of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-motor-top-end/197474-leaking-head-gasket-loose-head-bolts/page6?t=2074117&highlight=head+gasket&page=6)) | | ||
+ | |{{:techtalk:evo:engmech:removing_cylinder_stud_with_pipe_wrench_by_blue_scoot.jpg?direct&300|}}| | ||
+ | |||
+ | ==== Using Double Nuts / Jam Nuts ==== | ||
+ | Install 2 nuts on the top threads and torque the two nuts to 35ft pounds or higher. \\ | ||
+ | Be aware the tall studs can stretch if it takes too much torque to break them free. \\ | ||
+ | Be sure to use rags around the bore so as to not get any debris in the engine while removing the stud(s). \\ | ||
+ | |||
+ | | Three jam nuts used here. ((photo by A 4 liter V8 eater of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/148266-building-a-90-inch-sledge-hammer/page11#post3236162))| | ||
+ | |{{:techtalk:evo:engmech:tightening_cylinder_-_head_studs_by_a_4_liter_v8_eater.png?direct&300|}}| | ||
+ | |||
+ | ===== Cleaning the Case Threads ===== | ||
+ | The threads on the head studs as well as in the case need to be clean and free of rust / debris and they need to be straight in order to obtain proper torque on the heads. \\ | ||
+ | |||
+ | The photos below are of before (L) and after (R) chasing the case threads with a 3/8"x16 tap. \\ | ||
+ | The dirty threads will add preload to the torque readings and can easily give false readings on the wrench which could affect head gasket performance. \\ | ||
+ | |||
+ | {{:techtalk:evo:engmech:head_bolt_threads_before_chasing_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:head_bolt_threads_chased_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | ===== Stripped Case Threads ===== | ||
These could be repaired with Heli-coils. \\ | These could be repaired with Heli-coils. \\ | ||
But the repair must be straight with no wobble when drilling. \\ | But the repair must be straight with no wobble when drilling. \\ |