Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:evo:engmech03b [2019/08/01 04:49] hippysmack ↷ Links adapted because of a move operation |
techtalk:evo:engmech03b [2019/08/01 04:58] hippysmack ↷ Links adapted because of a move operation |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| This agrees with the assumption that only the first couple of threads do most of the holding. \\ | This agrees with the assumption that only the first couple of threads do most of the holding. \\ | ||
| - | {{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_1_by_reddtigger.jpg?direct&300|}} ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056)) \\ | + | {{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_1_by_reddtigger.jpg?direct&300|}} ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056)) \\ |
| There are many different options for fixing the stripped stud. This one was repaired using a Time-Sert kit. \\ | There are many different options for fixing the stripped stud. This one was repaired using a Time-Sert kit. \\ | ||
| Line 19: | Line 19: | ||
| The included bit with the kit wouldn't work using the guide. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056)) \\ | The included bit with the kit wouldn't work using the guide. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056)) \\ | ||
| - | |{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_2_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_3_by_reddtigger.jpg?direct&300|}}| | + | |{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_2_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_3_by_reddtigger.jpg?direct&300|}}| |
| So a holding jig for the engine was devised hold the slanted portion of the case in a level and upright position. \\ | So a holding jig for the engine was devised hold the slanted portion of the case in a level and upright position. \\ | ||
| Line 29: | Line 29: | ||
| **Homemade jig**: ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056)) \\ | **Homemade jig**: ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056)) \\ | ||
| - | |{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_4_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_5_by_reddtigger.jpg?direct&200|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_6_by_reddtigger.jpg?direct&300|}}| | + | |{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_4_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_5_by_reddtigger.jpg?direct&200|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_6_by_reddtigger.jpg?direct&300|}}| |
| With the cylinder in place on the case, a construction type level was placed on top to insure it was level before drilling. \\ | With the cylinder in place on the case, a construction type level was placed on top to insure it was level before drilling. \\ | ||
| Line 41: | Line 41: | ||
| **Positioning the engine**: \\ | **Positioning the engine**: \\ | ||
| |Getting it level. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Protecting the insides. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Positioning the drill press. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))| | |Getting it level. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Protecting the insides. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Positioning the drill press. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))| | ||
| - | |{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_7_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_8_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_9_by_reddtigger.jpg?direct&250|}}| | + | |{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_7_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_8_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_9_by_reddtigger.jpg?direct&250|}}| |
| A 19/64" drill bit (which just barely fit inside the existing hole) was used to ensure the drill press was aligned to the hole. \\ | A 19/64" drill bit (which just barely fit inside the existing hole) was used to ensure the drill press was aligned to the hole. \\ | ||
| Line 66: | Line 66: | ||
| |Testing the bit for straightness in the hole. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Using multiple drill bits. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Using a drill stop. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))| | |Testing the bit for straightness in the hole. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Using multiple drill bits. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Using a drill stop. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))| | ||
| - | |{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_10_by_reddtigger.jpg?direct&250|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_11_by_reddtigger.jpg?direct&150|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_12_by_reddtigger.jpg?direct&250|}}| | + | |{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_10_by_reddtigger.jpg?direct&250|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_11_by_reddtigger.jpg?direct&150|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_12_by_reddtigger.jpg?direct&250|}}| |
| Once the hole is drilled with the X Bit, then you use the counter bore bit, it has a built in stop so you can't go to far. \\ | Once the hole is drilled with the X Bit, then you use the counter bore bit, it has a built in stop so you can't go to far. \\ | ||
| Line 77: | Line 77: | ||
| |Time Sert kit as recieved. (also with instructions and \\ a couple extra inserts) ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Hole drilled and cleaned. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Tap the hole using the guide. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))| | |Time Sert kit as recieved. (also with instructions and \\ a couple extra inserts) ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Hole drilled and cleaned. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))|Tap the hole using the guide. ((photo by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))| | ||
| - | |{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_13_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_14_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_15_by_reddtigger.jpg?direct&200|}}| | + | |{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_13_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_14_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_15_by_reddtigger.jpg?direct&200|}}| |
| Let it sit for about 15 min. and install the insert. \\ | Let it sit for about 15 min. and install the insert. \\ | ||
| Line 88: | Line 88: | ||
| |Now the insert is installed flush with the base gasket surface and sitting awaiting for insert of the cylinder stud. \\ The new studs come with Loctite already on them. ((photos by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))||| | |Now the insert is installed flush with the base gasket surface and sitting awaiting for insert of the cylinder stud. \\ The new studs come with Loctite already on them. ((photos by ReddTigger of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1704056))||| | ||
| - | |{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_16_by_reddtigger.jpg?direct&300|}}|{{techtalk:ref:engmech:time-sert_cylinder_bolt_repair_17_by_reddtigger.jpg?direct&200|}}|{{techtalk:ref:genmsr:time-sert_cylinder_bolt_repair_18_by_reddtigger.jpg?direct&300|}}| | + | |{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_16_by_reddtigger.jpg?direct&300|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_17_by_reddtigger.jpg?direct&200|}}|{{techtalk:evo:engmech:time-sert_cylinder_bolt_repair_18_by_reddtigger.jpg?direct&300|}}| |
