Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:evo:oil04c [2019/07/24 04:59] hippysmack [07 Style Oil Cap with Homemade Temperature Gauge] |
— (current) | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== EVO: Oiling & Lubrication - Sub-04C ====== | ||
- | ====== 07 Style Oil Cap with Homemade Temperature Gauge ====== | ||
- | Article by ridinfool of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=887399)) | ||
- | Sometimes you have to be innovative to save some cash. \\ | ||
- | This oil temp gauge was devised for about $20 as opposed to the $45 one from the MoCo. \\ | ||
- | |||
- | {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_7_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_8_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) | ||
- | |||
- | Parts & Tools: \\ | ||
- | One meat thermometer either instant read dial or digit read. \\ | ||
- | Some JB Weld. \\ | ||
- | Drill / bit. | ||
- | |||
- | Take the oil cap apart as shown below. \\ | ||
- | Then cut the dipstick off flush with bottom of the cap. \\ | ||
- | |||
- | {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_1_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_2_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_3_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) | ||
- | |||
- | Drill a hole just a bit smaller than the thermometer rod through the center so it fits snug. \\ | ||
- | Then drill a hole through the top of the oil cap. \\ | ||
- | Going through the bottom, there is a plastic piece that guides the drill bit. \\ | ||
- | Slide the meat thermometer in place with some JB weld on the bottom of it so it stays in place. \\ | ||
- | (make sure not to get the JB Weld on the rod itself as it needs to go up and down with the oil cap) \\ | ||
- | |||
- | {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_4_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_5_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) {{:techtalk:evo:oil:07_up_homemade_oil_temp_cap_6_by_ridinfool.jpg?direct&300|}} ((photo by http://xlforum.net/forums/showthread.php?t=887399)) | ||
- | |||
- | |||
- | \\ | ||
- | |||
- | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |