Differences

This shows you the differences between two versions of the page.

--- techtalk:evo:susp03 [2019/02/28 03:23]
ixl2relax [Rubber Mount Bikes]
+++ techtalk:evo:susp03 [2019/12/06 22:56]
hippysmack [Sub Documents]
@@ Line 6: / Line 6: @@
 ====== Swingarm ======
 \\
-===== Swingarm & Bearing ======
-The swingarm has only one bearing. It is on the right side pivot. The left side pivot, 1986-2003, uses a bushing, not a bearing. The 2004-later models, the left side pivot is incorporated in the rear rubber motor mount.
+===== Rigid Mount Bikes =====
+==== Sub Documents ====
-| REAR FORK WITH BEARING || RIGHT BEARING ONLY | LEFT BUSHING |
+  * [[techtalk:evo:susp03a|Rigid Mount Swingarm Bearing / Bushing Inspection and Replacement]]
-| 1986 | 47532-86 | 47082-81 | 47083-81A |
-| 1987-1999 | 47547-87B | ::: | ::: |
-| 2000-2003 | 47587-00 | 48367-98 | ::: |
+{{ :techtalk:evo:susp:2002_swingarm_1_by_spibbie.jpg?direct&350|}}
-| 2004 | 47587-04 | 9209 | N/U |
+-88 models are shown to have two bearings and 89-03 models with only one bearing in the catalogs. \\
-| 2005-2018 | 47587-05A | ::: | ::: |
+However, two bearings are used in 86-03 Sportster swingarms and they are both installed on the right side pivot.  ((1986-1988 HD Sportster Parts Catalog 99451-88 pg 67)) ((1986-1989 HD Sportster Parts Catalog 99451-89 pg 69))  ((1986-1990 HD Sportster Parts Catalog 99451-90 pg 69)) ((1991 HD Sportster Parts Catalog 99451-91 pg 61)) ((1991-1992 HD Sportster Parts Catalog 99451-92 pg 63)) ((1993 HD Sportster Parts Catalog 99451-93 pg 63)) ((1993-1994 HD Sportster Parts Catalog 99451-94 pg 63)) ((1995 HD Sportster Parts Catalog 99451-95 pg 61)) ((1995-1996 HD Sportster Parts Catalog 99451-96 pg 65)) ((1997 HD Sportster Parts Catalog 99451-97 pg 65)) ((1998 HD Sportster Parts Catalog 99451-98 pg 67)) ((1999 HD Sportster Parts Catalog 99451-99 pg 73)) ((2000 HD Sportster Parts Catalog 99451-00A pg 73)) ((2001 HDSportster Parts Catalog 99451-01A pg 75)) ((2002 HD Sportster Parts Catalog 99451-02 pg 75)) ((2003 HD Sportster Parts Catalog 99451-03 pg 75)) \\
+Both left and right sides were described as having bearings until the 2000 parts book came out correctly describing the left side as having a bushing. \\
+The part number for the bearing (set) changed in 2000 from (47082-81) to (48367-98). \\
+According to the pics on the [[https://www.jwboon.com/index2.php?co...rtster/Page_15|JW Boon]] website for NOS parts, even though the part number changed for the right bearing, it appears to be a place of origin change. \\
+Both part numbers refer to a 'Timken LM11749' bearing: (47082-81 made in Poland) and (48367-98 made in USA). ((Hippysmack of the XLFORUM http://xlforum.net/forums/showthread.php?p=5790716#post5790716)) \\
+The Prefix designates the duty class: LL - Lighter than Light; L - Light; LM - Light Medium; M - Medium; HM - Heavy Medium, H - Heavy ((https://www.motionindustries.com/productDetail.jsp?sku=00657537)) ((photo by spibbie of the XLFORUM, annotated by Hippysmack http://xlforum.net/forums/showthread.php?t=1861454&page=2))
+**Swingarm with bearing(s) and bushings**. \\
+|**Note**: Inspect pivot shaft and swingarm bearings every 5,000 miles. \\ Lube swingarm bearings every 10,0000 miles. ((1998 HD Sportster FSM pg 1-2))|||||
+| **REAR FORK WITH RIGHT BEARING** || **LEFT BUSHING** | **RIGHT BEARING ONLY** |  **BEARING OUTER RACE**  |
+| 1986-1987 XLH 883/DLX \\ XLH 1100 | 47532-86 | (1) 47083-81 | (2) 47082-81 \\ (Timken LM11749) \\ Poland PC X0242 ((https://www.jwboon.com/index2.php?content=https%3A//www.jwboon.com/dbhtml/catalog/Bool_AND/Section_frame/Fits_Sportster/Page_15)) |  (2) LM11710  |
+| 1987 XLH 883 Hug \\ 88 - all | 47547-87 | ::: | ::: |::: |
+| E1989 - all | ::: | ::: | ::: |::: |
+|L1989 - all |47566-89| ::: | ::: |::: |
+|1990 - all |47547-89 \\ (retro to L89)| ::: | ::: |::: |
+|1991- 1994 - all|47547-87A| ::: | ::: |::: |
+|1995-1998 - all |47547-87B| ::: | ::: |::: |
+|1999 - all |47547-87B| (1) 47083-81A  | ::: |::: |
+| 2000-2003 | 47587-00 | ::: | (2) 48367-98 \\ (Timken LM11749) \\ USA PS ((https://www.jwboon.com/index2.php?content=https%3A//www.jwboon.com/dbhtml/catalog/Bool_AND/Section_frame/Fits_Sportster/Page_15)) |::: |
+**Swingarm related parts** \\
+|  **Pivot Bolt**  |  **Pivot Bolt Screw**  |**Bearing Dust Shield** (2-right)|  **Pivot Bolt Spacer**  |  **Swingarm Hole Plug**  |
+| 86-88 (41568-86) \\ all models |86-88 (2892) \\ all models|86-03 (41579-81) \\ all models|86-03 (5741) \\ all models|86-96 / 99-03 (740) \\ all models|
+| 89-90 (41568-89) \\ all models |89-92 (2925) \\ all models|  |  |97-98 (761) \\ all models|
+| 91- 92 (41568-89A) \\ all models |93-03 (2925A) \\ all models \\ 3/8" Allen head|
+| 93-03 (41568-81B) \\ all models (1" hex head bolt)\\ includes pivot bolt screw & spacer |
-\\
-===== Rigid Mount Bikes =====
 ===== Rubber Mount Bikes =====
+For the 2004-later models, the swingarm uses a bearing in each side and the assembly is part of the motor mounting system as well. \\
+See [[techtalk:evo:susp05#rubber_mount_engine_mounts|Rubber Mount Engine Mounts]] in the Sportsterpedia for assembly including the swingarm. \\
-Notes gathered from the XLFORUM:
+| **REAR FORK WITH 2 BEARINGS** ||  **LEFT OR RIGHT BEARING ONLY**  ||
+| 2004 | 47587-04 |  9209  ||
+| 2005-2018 | 47587-05A | ::: ||
+swingarm and bearings from an 883. \\
+{{:techtalk:evo:susp:04_883_swingarm_15_by_dede.jpg?direct&400|}} ((photo by DéDé of the XLFORUM http://xlforum.net/forums/showthread.php?p=5770909)) {{:techtalk:evo:susp:04_883_swingarm_16_by_dede.jpg?direct&300|}} ((photo by DéDé of the XLFORUM http://xlforum.net/forums/showthread.php?p=5770909)) \\
+Notes gathered from the XLFORUM: \\
@@ Line 54: / Line 91: @@
+If you are replacing the bearings, it's worth reading this extensive thread about replacing the engine rubber mounts: http://xlforum.net/forums/showthread.php?t=1526368

Trace:

Differences

Navigation

Search

Toolbox