Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:evo:susp03e [2020/06/13 18:37] hippysmack [Bearing Lockring] |
techtalk:evo:susp03e [2021/02/02 06:34] hippysmack [Bearing Lockring] |
||
---|---|---|---|
Line 5: | Line 5: | ||
\\ | \\ | ||
+ | ===== Swingarm ===== | ||
+ | \\ | ||
+ | ==== 1995-1998 Swingarm (47547-87B) ==== | ||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_8_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | ===== Swingarm Pivot Bolt ===== | ||
+ | \\ | ||
+ | ==== 1993-2003 Pivot Bolt (41568-81B) ==== | ||
+ | |||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_pivot_bolt_dims_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
===== Bearing Lockring ===== | ===== Bearing Lockring ===== | ||
Line 11: | Line 25: | ||
It has no part number as it comes in a set with the bearings. \\ | It has no part number as it comes in a set with the bearings. \\ | ||
It's actually just a retaining ring acting as both a stop and a spacer between each bearing race when they are installed. \\ | It's actually just a retaining ring acting as both a stop and a spacer between each bearing race when they are installed. \\ | ||
- | Officially, it's a Constant Section Internal Retaining Ring. \\ | + | |
+ | Officially, it's a Constant Section Internal Retaining Ring (AKA, Eaton-style or horseshoe snap rings) of the "Bearing Snap Ring" variety. ((https://www.prospectfastener.com/snaprings/internalrings/constant-section-internal-rings)) \\ | ||
It features a uniform, constant section. This means that the material used to make the ring is the same width at any point along the circumference of the ring. \\ | It features a uniform, constant section. This means that the material used to make the ring is the same width at any point along the circumference of the ring. \\ | ||
This allows full seat of the races against it as they are installed. \\ | This allows full seat of the races against it as they are installed. \\ | ||
+ | These can be bought from fastener companies in carbon steel as plain or with oil embedded. \\ | ||
This is a NOS ring. \\ | This is a NOS ring. \\ | ||
Line 53: | Line 69: | ||
{{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
- | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | + | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack))\\ |
===== Bearing Dust Shield ===== | ===== Bearing Dust Shield ===== | ||