Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:evo:susp03e [2020/05/25 06:32] hippysmack [Bearing Lockring] |
techtalk:evo:susp03e [2022/02/11 17:35] (current) hippysmack [Dimensions for Rigid Mount Swingarm and Parts] |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== EVO: Suspension - Sub-03E ====== | ====== EVO: Suspension - Sub-03E ====== | ||
- | ====== Dimensions for Rigid Mount Swingarm and Parts ====== | + | ====== 1995-1998 Swingarm (47547-87B) and Parts Dimensions ====== |
\\ | \\ | ||
+ | ===== Swingarm ===== | ||
+ | \\ | ||
+ | ==== 1995-1998 Swingarm (47547-87B) ==== | ||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_8_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | ===== Swingarm Pivot Bolt ===== | ||
+ | \\ | ||
+ | ==== 1993-2003 Pivot Bolt (41568-81B) ==== | ||
+ | |||
+ | {{:techtalk:evo:susp:1998_sportster_swingarm_pivot_bolt_dims_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
===== Bearing Lockring ===== | ===== Bearing Lockring ===== | ||
Line 11: | Line 25: | ||
It has no part number as it comes in a set with the bearings. \\ | It has no part number as it comes in a set with the bearings. \\ | ||
It's actually just a retaining ring acting as both a stop and a spacer between each bearing race when they are installed. \\ | It's actually just a retaining ring acting as both a stop and a spacer between each bearing race when they are installed. \\ | ||
+ | |||
+ | Officially, it's a Constant Section Internal Retaining Ring (AKA, Eaton-style or horseshoe snap rings) of the "Bearing Snap Ring" variety. ((https://www.prospectfastener.com/snaprings/internalrings/constant-section-internal-rings)) \\ | ||
+ | It features a uniform, constant section. This means that the material used to make the ring is the same width at any point along the circumference of the ring. \\ | ||
+ | This allows full seat of the races against it as they are installed. \\ | ||
+ | These can be bought from fastener companies in carbon steel as plain or with oil embedded. \\ | ||
This is a NOS ring. \\ | This is a NOS ring. \\ | ||
Line 23: | Line 42: | ||
It has no part number as it comes in a set with the bearings. \\ | It has no part number as it comes in a set with the bearings. \\ | ||
+ | This is a NOS ring. \\ | ||
{{:techtalk:evo:susp:swingarm_bearing_spacer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | {{:techtalk:evo:susp:swingarm_bearing_spacer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
{{:techtalk:evo:susp:swingarm_bearing_spacer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | {{:techtalk:evo:susp:swingarm_bearing_spacer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
Line 33: | Line 53: | ||
This bushing sets the length measurement for the proper clamp force on the swingarm part assembly and acts as a spacer bushing thru the left pivot. \\ | This bushing sets the length measurement for the proper clamp force on the swingarm part assembly and acts as a spacer bushing thru the left pivot. \\ | ||
+ | This is a used spacer. \\ | ||
{{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
{{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | ===== Pivot Spacer Bushing ===== | ||
+ | |||
+ | Used on 1986-2003, all models and 1982-1985 square tube swingarms. \\ | ||
+ | This bushing is installed in the left pivot and the pivot spacer is installed into this bushing. \\ | ||
+ | |||
+ | Below are dims for the replacement bushing from V-twin. \\ | ||
+ | |||
+ | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
+ | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
+ | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack))\\ | ||
===== Bearing Dust Shield ===== | ===== Bearing Dust Shield ===== | ||
Line 42: | Line 75: | ||
Part# (41579-81), 2 required. \\ | Part# (41579-81), 2 required. \\ | ||
+ | This is a used dust shield. \\ | ||
{{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||