Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:trouble01 [2017/10/24 16:18] ixl2relax [Setting TSM/HFSM and ECM Password] |
techtalk:evo:trouble01 [2018/04/18 01:37] ixl2relax |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| ====== EVO: Specific Troubleshooting ====== | ====== EVO: Specific Troubleshooting ====== | ||
| + | |||
| + | |||
| + | ====== General Practices & Procedures ====== | ||
| \\ | \\ | ||
| - | ====== ECM Password Learn Procedure ====== ((contributed by Screw Loose Dan)) | + | ====== ECM Password Learn Procedure ====== |
| The TSM/TSSM modules share a password with the ECM on fuel injected bikes (and ICM's on early rubber mount bikes). When replacing an ECM/ICM or TSSM, you must go through a password learn procedure. If the procedure is not followed, the engine will start and run for a few seconds, and then stall. This will typically throw a P1009 diagnostic code. | The TSM/TSSM modules share a password with the ECM on fuel injected bikes (and ICM's on early rubber mount bikes). When replacing an ECM/ICM or TSSM, you must go through a password learn procedure. If the procedure is not followed, the engine will start and run for a few seconds, and then stall. This will typically throw a P1009 diagnostic code. | ||
| Line 10: | Line 13: | ||
| You will typically want to connect your motorcycle up to a charger and pull the headlight fuse before starting these procedures. The procedure MUST be followed from start to finish without any interruption. If interrupted, starting over from the beginning is the only option. | You will typically want to connect your motorcycle up to a charger and pull the headlight fuse before starting these procedures. The procedure MUST be followed from start to finish without any interruption. If interrupted, starting over from the beginning is the only option. | ||
| - | For information about removing/replacing the TSM/TSSM, click this [[http://xlforum.net/vbportal/forums/showthread.php?t=573200|XLForum Thread]] by Cosmo on the topic. | + | For information about removing/replacing the TSM/TSSM, click this [[http://xlforum.net/forums/showthread.php?t=573200|XLForum Thread]] by Cosmo on the topic. |
| - | The table below is from the 2007 Harley-Davidson Sportster Electrical Diagnostic Manual (Section 3.25, pg 3-72): | + | ^ Device Replaced ^ Password Learn\\ Procedure Required? | ((See 2007 Harley-Davidson Sportster Electrical Diagnostic Manual Section 3.25, pg 3-72)) | |
| - | ^ Device Replaced ^ Password Learn Procedure Required? ^ | + | | ECM | Yes || |
| - | | ECM | Yes | | + | | TSM | No* || |
| - | | TSM | No* | | + | |TSSM | Yes || |
| - | |TSSM | Yes | | + | |
| *If a TSM has been replaced with a HFSM, or a HFSM has been replaced by a TSM, password **is** necessary. | *If a TSM has been replaced with a HFSM, or a HFSM has been replaced by a TSM, password **is** necessary. | ||
| - | ===== Setting TSM/HFSM and ECM Password ===== (( See 2007 Sportster Electrical Diagnostic Manual - Section 3.25, pg 3-73 )) | ||
| - | ^ Step # ^ Action ^ Confirmation ^ Notes ^ | + | ===== Setting TSM/HFSM and ECM Password ===== |
| - | | | Ignition must be turned off for at least 15 seconds. | With ignition turned off, Check Engine Lamp and Security Lamp will be off. | | | + | |
| - | | 1 | Install new TSM/HFSM or ECM. | | | | + | |
| - | | 2 | Set **RUN/OFF** switch to **RUN**. | | | | + | |
| - | | 3 | Turn **IGN** key **ON**. | Verify Check Engine Lamp and Security Lamp illuminate and then turn off. | TSM/HFSM enables starter relay.| | + | |
| - | | 4 | Attempt normal start **one** time. | Engine starts and stalls. Check Engine Lamp illuminates and stays on. | Password has not been learned. ECM sets DTC P1009. | | + | |
| - | | 5 | Wait ten seconds. Security lamp will illuminate and stay on. | Security Lamp illuminates. | ECM enters Password Learning mode for ten minutes. Do not cycle ignition switch or interrupt vehicle power or Password Learn will be unsuccessful.| | + | |
| - | | 6 | Wait until Security Lamp turns off. | | This takes ten minutes. (If no speedo or security light is available, wait **at least 10 minutes**.) | | + | |
| - | | 7 | Quickly (within two seconds) turn **IGN** key OFF-**ON**. | | ECM must not be allowed to shutdown. | | + | |
| - | | 8 | Wait until Security Lamp turns off. | | This takes ten minutes. (If no speedo or security light is available, wait **at least 10 minutes**.) | | + | |
| - | | 9 | Quickly (within two seconds) turn **IGN** key OFF-**ON**. | | ECM must not be allowed to shutdown. | | + | |
| - | | 10 | Wait until Security Lamp turns off. | | This takes ten minutes. (If no speedo or security light is available, wait **at least 10 minutes**.) | | + | |
| - | | 11 | Quickly (within two seconds) turn **IGN** key OFF-**ON**. | | ECM must not be allowed to shutdown. | | + | |
| - | | 12 | Turn **IGN** key **OFF**. __Wait 15 seconds before turning IGN on__. Turn **IGN** switch **ON** and start engine to confirm successful Password Learn procedure. Clear diagnostic trouble codes. | | | | + | |
| - | | 13 | If the learn procedure is interrupted or fails in any way, you must restart your attempt from the beginning of the procecure ||| | + | |
| + | ^ Step # ^ Action ^ Confirmation ^ Notes | ((See 2007 Harley-Davidson Sportster Electrical Diagnostic Manual Section 3.25, pg 3-73)) | | ||
| + | | | Ignition must be turned off for at least 15 seconds. | With ignition turned off, Check Engine Lamp and Security Lamp will be off. | || | ||
| + | | 1 | Install new TSM/HFSM or ECM. | | || | ||
| + | | 2 | Set **RUN/OFF** switch to **RUN**. | | || | ||
| + | | 3 | Turn **IGN** key **ON**. | Verify Check Engine Lamp and Security Lamp illuminate and then turn off. | TSM/HFSM enables starter relay.|| | ||
| + | | 4 | Attempt normal start **one** time. | Engine starts and stalls. Check Engine Lamp illuminates and stays on. | Password has not been learned. ECM sets DTC P1009. || | ||
| + | | 5 | Wait ten seconds. Security lamp will illuminate and stay on. | Security Lamp illuminates. | ECM enters Password Learning mode for ten minutes. Do not cycle ignition switch or interrupt vehicle power or Password Learn will be unsuccessful.|| | ||
| + | | 6 | Wait until Security Lamp turns off. | | This takes ten minutes. (If no speedo or security light is available, wait **at least 10 minutes**.) || | ||
| + | | 7 | Quickly (within two seconds) turn **IGN** key OFF-**ON**. | | ECM must not be allowed to shutdown. || | ||
| + | | 8 | Wait until Security Lamp turns off. | | This takes ten minutes. (If no speedo or security light is available, wait **at least 10 minutes**.) || | ||
| + | | 9 | Quickly (within two seconds) turn **IGN** key OFF-**ON**. | | ECM must not be allowed to shutdown. || | ||
| + | | 10 | Wait until Security Lamp turns off. | | This takes ten minutes. (If no speedo or security light is available, wait **at least 10 minutes**.) || | ||
| + | | 11 | Quickly (within two seconds) turn **IGN** key OFF-**ON**. | | ECM must not be allowed to shutdown. || | ||
| + | | 12 | Turn **IGN** key **OFF**. __Wait 15 seconds before turning IGN on__. Turn **IGN** switch **ON** and start engine to confirm successful Password Learn procedure. Clear diagnostic trouble codes. | | || | ||
| + | | 13 | If the learn procedure is interrupted or fails in any way, you must restart your attempt from the beginning of the procecure |||| | ||
| + | (This section contributed by Screw Loose Dan ) | ||
| \\ | \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
