Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
techtalk:ih:carb01b [2020/04/01 20:12] hippysmack [IH: Carburetor, Intake Manifold & Exhaust Systems - Sub-01B] |
techtalk:ih:carb01b [2023/12/28 22:04] hippysmack |
||
|---|---|---|---|
| Line 7: | Line 7: | ||
| * [[techtalk:ih:carb01a|Linkert Carb Identification]] | * [[techtalk:ih:carb01a|Linkert Carb Identification]] | ||
| * [[techtalk:ih:carb01c|Linkert Carb Functions, Adjustments, Tuning]] | * [[techtalk:ih:carb01c|Linkert Carb Functions, Adjustments, Tuning]] | ||
| + | |||
| ====== Cleaning ====== | ====== Cleaning ====== | ||
| * The general appearance of the inside of the carb is not necessarily a good indication of its condition. \\ It can look spotless and have clogged jets, or look cruddy and have clear jets. | * The general appearance of the inside of the carb is not necessarily a good indication of its condition. \\ It can look spotless and have clogged jets, or look cruddy and have clear jets. | ||
| Line 15: | Line 16: | ||
| * An overnight soak in a solution of Pinesol and water followed up with a good brush down with a toothbrush then rinse and air dry. ((http://www.hotrodders.com/forum/pinesol-really-does-clean-carburetors-amazingly-pics-inside-248810.html)) \\ See also [[techtalk:ref:tools127#general_cleaning_and_stuck_gaskets|Soaking parts]] in the REF section of the Sportsterpedia. | * An overnight soak in a solution of Pinesol and water followed up with a good brush down with a toothbrush then rinse and air dry. ((http://www.hotrodders.com/forum/pinesol-really-does-clean-carburetors-amazingly-pics-inside-248810.html)) \\ See also [[techtalk:ref:tools127#general_cleaning_and_stuck_gaskets|Soaking parts]] in the REF section of the Sportsterpedia. | ||
| * A 20 minute to up to a few days soak in a gallon of Gunk (or other) Carburetor Cleaner that has a basket inside for small parts and lowers in the can with a handle, rinse, air dry, use. | * A 20 minute to up to a few days soak in a gallon of Gunk (or other) Carburetor Cleaner that has a basket inside for small parts and lowers in the can with a handle, rinse, air dry, use. | ||
| - | * Soak it in mineral spirits for a few days. ((Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=185361)) | + | * Soak it in mineral spirits for a few days. ((Monte03 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/47937-cleaning-a-carb?t=185361)) |
| - | * You can use acrylic paint thinners for cleaning up carb parts. It melts the fuel varnish right off. ((russzx6 of the XLFORUM http://xlforum.net/forums/showthread.php?t=185361)) | + | * You can use acrylic paint thinners for cleaning up carb parts. It melts the fuel varnish right off. ((russzx6 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/47937-cleaning-a-carb?t=185361)) |
| * An aerosol spray carb cleaner will also work but may not loosen all of the build up in the jets or orifices in the carb body if they're not directly sprayed through. | * An aerosol spray carb cleaner will also work but may not loosen all of the build up in the jets or orifices in the carb body if they're not directly sprayed through. | ||
| * Blow out all holes, jets and orifices thoroughly with compressed air after cleaning. | * Blow out all holes, jets and orifices thoroughly with compressed air after cleaning. | ||
| Line 25: | Line 26: | ||
| Make sure to remove any rubber or plastic parts before soaking. Also check the label for safety precautions. \\ | Make sure to remove any rubber or plastic parts before soaking. Also check the label for safety precautions. \\ | ||
| Parts that have been sitting for years may have to be soaked for about 24 hours or even days. \\ | Parts that have been sitting for years may have to be soaked for about 24 hours or even days. \\ | ||
| - | | Carburetor Cleaner ((photo by Hippysmack)) || | + | | Carburetor Cleaner ((photos by Hippysmack)) || |
| |{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}| | |{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}| | ||
| Line 40: | Line 41: | ||
| However, this setup works better than putting the carb directly into the vice. \\ | However, this setup works better than putting the carb directly into the vice. \\ | ||
| The carb is set upright as 'in use' making adjustments more straight forward. \\ | The carb is set upright as 'in use' making adjustments more straight forward. \\ | ||
| - | {{:techtalk:ref:tools:carb_stand_1_by_ironmick.jpg?direct&150|}} ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=185361)) | + | {{:techtalk:ref:tools:carb_stand_1_by_ironmick.jpg?direct&150|}} ((photo by IronMick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/47937-cleaning-a-carb?t=185361)) |
| {{:techtalk:ih:carb:bendix-zenith_carb_12_by_the_doctor71_of_the_xlforum.jpg?direct&200|}} | {{:techtalk:ih:carb:bendix-zenith_carb_12_by_the_doctor71_of_the_xlforum.jpg?direct&200|}} | ||
| ((Pic courtesy of The Doctor71 of the XLFORUM)) \\ | ((Pic courtesy of The Doctor71 of the XLFORUM)) \\ | ||
| Line 51: | Line 52: | ||
| * Whenever a welsh plug is removed, a new one should be installed in it's place, especially since a large part of the time, removal of one means destroying or deforming it.((1959-1969 HD Sportster FSM)) | * Whenever a welsh plug is removed, a new one should be installed in it's place, especially since a large part of the time, removal of one means destroying or deforming it.((1959-1969 HD Sportster FSM)) | ||
| * Drill an 1/8" hole thru it (just deep enough to break thru to the other side) off center and pry it out with a small punch. Be careful not to drill too deep which could destroy the nozzle assembly or casting. While prying it out, be careful not to damage the casting counter-bore edges around the plug. | * Drill an 1/8" hole thru it (just deep enough to break thru to the other side) off center and pry it out with a small punch. Be careful not to drill too deep which could destroy the nozzle assembly or casting. While prying it out, be careful not to damage the casting counter-bore edges around the plug. | ||
| - | * You can also drill a small hole in it and use a small tap just big enough to start in the hole. ((snake173 of the XLFORUM http://xlforum.net/forums/showpost.php?p=3646523&postcount=1)) \\ Thread the tap in the hole. \\ When it gets to the bottom of the passage, it will force the valve out with out damaging the bottom of carb passage. \\ Make sure to clean all the chips out to keep from plugging up passages later. | + | * You can also drill a small hole in it and use a small tap just big enough to start in the hole. ((snake173 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/108002-zenith-bendix-carb-rebuild-kits/page3?postcount=1#post2687578)) \\ Thread the tap in the hole. \\ When it gets to the bottom of the passage, it will force the valve out with out damaging the bottom of carb passage. \\ Make sure to clean all the chips out to keep from plugging up passages later. |
| * Installation: ((HD Service Bulletin #518 dated September 10, 1965 pg OC-189))((1959-1969 HD Sportster FSM)). | * Installation: ((HD Service Bulletin #518 dated September 10, 1965 pg OC-189))((1959-1969 HD Sportster FSM)). | ||
| * The plug should be seated with a flat end punch that is slightly smaller than the diameter of the plug. The plug should be flat and not concaved to assure a tight fit. If leakage is suspected due to a rough or damaged welch plug seat in the casting, apply a small amount of epoxy or suitable sealant to the edges after installing it. | * The plug should be seated with a flat end punch that is slightly smaller than the diameter of the plug. The plug should be flat and not concaved to assure a tight fit. If leakage is suspected due to a rough or damaged welch plug seat in the casting, apply a small amount of epoxy or suitable sealant to the edges after installing it. | ||
