Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ih:carb01l [2019/10/06 01:27] hippysmack [Pump diaphragm] |
techtalk:ih:carb01l [2019/10/08 03:39] hippysmack [Cleaning] |
||
|---|---|---|---|
| Line 14: | Line 14: | ||
| * Examine all parts for excessive wear, damage, distortion, etc. | * Examine all parts for excessive wear, damage, distortion, etc. | ||
| * Cleaning solutions/sprays vary based upon your location, needs, budget, preferences and quality. \\ Dismantle the carb down to the body before soaking. You will be surprised at all the dirt in the bottom of the soaking container. \\ Here are some helpful ideas: | * Cleaning solutions/sprays vary based upon your location, needs, budget, preferences and quality. \\ Dismantle the carb down to the body before soaking. You will be surprised at all the dirt in the bottom of the soaking container. \\ Here are some helpful ideas: | ||
| - | * An overnight soak in a solution of Pinesol and water followed up with a good brush down with a toothbrush then rinse and air dry. ((http://www.hotrodders.com/forum/pinesol-really-does-clean-carburetors-amazingly-pics-inside-248810.html)) | + | * An overnight soak in a solution of Pinesol and water followed up with a good brush down with a toothbrush then rinse and air dry. ((http://www.hotrodders.com/forum/pinesol-really-does-clean-carburetors-amazingly-pics-inside-248810.html)) \\ See also [[techtalk:ref:tools127#general_cleaning_and_stuck_gaskets|Soaking parts]] in the REF section of the Sportsterpedia. |
| * A 20 minute to up to a few days soak in a gallon of Gunk (or other) Carburetor Cleaner that has a basket inside for small parts and lowers in the can with a handle, rinse, air dry, use. | * A 20 minute to up to a few days soak in a gallon of Gunk (or other) Carburetor Cleaner that has a basket inside for small parts and lowers in the can with a handle, rinse, air dry, use. | ||
| * Soak it in mineral spirits for a few days. ((Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=185361)) | * Soak it in mineral spirits for a few days. ((Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=185361)) | ||
| Line 203: | Line 203: | ||
| ==== Accelerator pump shaft ==== | ==== Accelerator pump shaft ==== | ||
| + | Inspect the accelerator pump rod for bending. Inspect the rubber boot for cracks / tears. Any dirt that gets past the boot into the accelerator pump passage should be blown out from the side opposite of the nozzle (or check valve will close, making cleaning impossible). \\ | ||
| {{ :techtalk:ih:carb:bendix_carb_and_parts_by_schutzhund9.jpg?direct&300| }} \\ | {{ :techtalk:ih:carb:bendix_carb_and_parts_by_schutzhund9.jpg?direct&300| }} \\ | ||
| Line 211: | Line 211: | ||
| You can use most of the parts in this kit but purchase the Harley Part (#27762-71TA). \\ | You can use most of the parts in this kit but purchase the Harley Part (#27762-71TA). \\ | ||
| Aftermarket rebuild kit: \\ | Aftermarket rebuild kit: \\ | ||
| - | |||
| There are 3 holes in the accelerator pump shaft to provide more or less fuel upon acceleration. \\ | There are 3 holes in the accelerator pump shaft to provide more or less fuel upon acceleration. \\ | ||
