Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ih:carb01m [2019/09/13 17:05] hippysmack [Throttle Cable] |
techtalk:ih:carb01m [2019/09/21 15:10] hippysmack [Check Valve] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| \\ | \\ | ||
| ====== Bendix Zenith I6P12 Carb (1972-Early 1976) ====== | ====== Bendix Zenith I6P12 Carb (1972-Early 1976) ====== | ||
| - | \\ | ||
| See also in the Sportsterpedia: \\ | See also in the Sportsterpedia: \\ | ||
| - | * [[techtalk:ih:carb01#bendix_zenith_i6p12_carb_1972-early_1976|Bendix basic carb information]] | + | * [[techtalk:ih:carb01#bendix_zenith_i6p12_carb_1972-early_1976|Bendix Carb Basic Information]] |
| * [[techtalk:ih:carb01k|Bendix Carb Identification]] | * [[techtalk:ih:carb01k|Bendix Carb Identification]] | ||
| * [[techtalk:ih:carb01l|Rebuilding the Bendix Carb]] | * [[techtalk:ih:carb01l|Rebuilding the Bendix Carb]] | ||
| + | |||
| Line 61: | Line 61: | ||
| ===== Float ===== | ===== Float ===== | ||
| + | |||
| + | ===== Check Valve ===== | ||
| + | The check valve has two main functions. | ||
| + | - It feeds gas to the accelerator passage in the bottom of the bowl. | ||
| + | - It seals off the main fuel supply between the bowl and the accel pump passage when the pump is actuated. | ||
| + | |||
| + | The disc is left loose by the tabs in the normal relaxed state to allow gas to enter the accel passage below. \\. \\ | ||
| + | Then it is seated when the pump shaft is actuated by way of pressure created in the accel passage of the bowl which pushes the disc up into the seat. \\ | ||
| + | |||
| + | {{:techtalk:ih:carb:original_bendix_check_valve_1_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074658)) | ||
| + | {{:techtalk:ih:carb:original_bendix_check_valve_2_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074658)) \\ | ||
| + | |||
| + | |||
| + | {{:techtalk:ih:carb:original_bendix_check_valve_3_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074658)) | ||
| + | {{:techtalk:ih:carb:original_bendix_check_valve_4_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074658)) | ||
| + | {{:techtalk:ih:carb:original_bendix_check_valve_5_by_the_doctor71.jpg?direct&300|}} ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074658)) \\ | ||
| ===== Choke Plate \ Cable ===== | ===== Choke Plate \ Cable ===== | ||
| Line 125: | Line 141: | ||
| {{:techtalk:ih:carb:bendix_carb_by_jdxlch.jpg?direct&300|}} ((photo by jdxlch of the XLFORUM http://xlforum.net/forums/showthread.php?t=1069639)) {{:techtalk:ih:carb:bendix_throttle_spring_by_russ_t_nail.jpg?direct&300|}} ((photo by Russ t nail of the XLFORUM http://xlforum.net/forums/showthread.php?t=1069639&page=5)) \\ | {{:techtalk:ih:carb:bendix_carb_by_jdxlch.jpg?direct&300|}} ((photo by jdxlch of the XLFORUM http://xlforum.net/forums/showthread.php?t=1069639)) {{:techtalk:ih:carb:bendix_throttle_spring_by_russ_t_nail.jpg?direct&300|}} ((photo by Russ t nail of the XLFORUM http://xlforum.net/forums/showthread.php?t=1069639&page=5)) \\ | ||
| + | |||
| + | Another option: \\ | ||
| + | {{:techtalk:ih:carb:bendix_throttle_cable_bracket_1_by_biged.jpg?direct&300|}} ((photo by biged of the XLFORUM http://xlforum.net/forums/showthread.php?t=757063)) {{:techtalk:ih:carb:bendix_throttle_cable_bracket_2_by_biged.jpg?direct&300|}} ((photo by biged of the XLFORUM http://xlforum.net/forums/showthread.php?t=757063)) \\ | ||
| Below, the existing bracket was modified. With two crescent wrenches and a rat tail file, the hole was enlarged almost to the end of the support. ((jdxlch of the XLFORUM http://xlforum.net/forums/showthread.php?t=1069639&page=2))\\ | Below, the existing bracket was modified. With two crescent wrenches and a rat tail file, the hole was enlarged almost to the end of the support. ((jdxlch of the XLFORUM http://xlforum.net/forums/showthread.php?t=1069639&page=2))\\ | ||
