Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ih:carb01q [2019/10/17 02:38] hippysmack [Idle Transfer Ports] |
techtalk:ih:carb01q [2020/04/01 20:17] hippysmack [IH: Carburetor, Intake Manifold & Exhaust Systems - Sub-01Q] |
||
---|---|---|---|
Line 176: | Line 176: | ||
* Check that the ports are not gunked up and are free of obstructions. | * Check that the ports are not gunked up and are free of obstructions. | ||
* Check that the Welch plug over the top of them isn't leaking. \\ It's good to remove any old sealer over the Welch plug and install some fresh. Read about [[techtalk:ih:carb01q#welch_plug|Welch Plugs]] below. | * Check that the Welch plug over the top of them isn't leaking. \\ It's good to remove any old sealer over the Welch plug and install some fresh. Read about [[techtalk:ih:carb01q#welch_plug|Welch Plugs]] below. | ||
+ | * If you've dunked the carb in carb cleaner, any sealant that was around the Welch plug would now be compromised and resealing is a must. | ||
===== Jets ===== | ===== Jets ===== | ||
{{:techtalk:ih:carb:keihin_jets_by_billblack_-_cropped-annotated.jpg?direct&400|}} ((photo by billblack of the XLFORUM, cropped & annotated by Hippysmack http://xlforum.net/forums/showthread.php?p=4770495&highlight=keihin+bowl#post4770495)) \\ | {{:techtalk:ih:carb:keihin_jets_by_billblack_-_cropped-annotated.jpg?direct&400|}} ((photo by billblack of the XLFORUM, cropped & annotated by Hippysmack http://xlforum.net/forums/showthread.php?p=4770495&highlight=keihin+bowl#post4770495)) \\ | ||
Line 375: | Line 375: | ||
{{:techtalk:ih:carb:86_keihin_carb_repair_1_by_bustakneecap.jpg?direct&300|}} ((photo by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?p=3864149)) {{:techtalk:ih:carb:86_keihin_carb_repair_2_by_bustakneecap.jpg?direct&300|}} ((photo by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?p=3864149)) {{:techtalk:ih:carb:86_keihin_carb_repair_3_by_bustakneecap.jpg?direct&300|}} ((photo by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?p=3864149)) \\ | {{:techtalk:ih:carb:86_keihin_carb_repair_1_by_bustakneecap.jpg?direct&300|}} ((photo by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?p=3864149)) {{:techtalk:ih:carb:86_keihin_carb_repair_2_by_bustakneecap.jpg?direct&300|}} ((photo by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?p=3864149)) {{:techtalk:ih:carb:86_keihin_carb_repair_3_by_bustakneecap.jpg?direct&300|}} ((photo by bustakneecap of the XLFORUM http://xlforum.net/forums/showthread.php?p=3864149)) \\ | ||
+ | ===== Choke Rod / Cable ===== | ||
+ | |||
+ | The old factory steel choke wire and the steel bracket works best. \\ | ||
+ | When the bike backfires, it resists slapping the choke shut. \\ | ||
+ | The cable type ones allow more flex at the bracket and subsequently the choke plate. \\ | ||
===== High Altitude Modification Kit ===== | ===== High Altitude Modification Kit ===== | ||