Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ih:elec03 [2019/07/02 23:42] hippysmack [Tachometers] |
techtalk:ih:elec03 [2019/10/08 14:17] hippysmack [Horn] |
||
---|---|---|---|
Line 173: | Line 173: | ||
| |68542-61|Pursuit lamps|F 421-6V|6| | | |68542-61|Pursuit lamps|F 421-6V|6| | ||
+ | ====== Horn ====== | ||
+ | This is a rebuild of the stock Delco Remy horn from a 68 XLCH. \\ | ||
+ | There are horn rebuild kits available, but they are pretty simple in design and a good cleaning may be all that is needed. \\ | ||
+ | The repop one from J&P Cycles is on the right (3rd pic below). It has 2 wire connections as opposed to the single wire connection on the original horn. \\ | ||
+ | |||
+ | {{:techtalk:ih:elec:delco-remy_horn_rebuild_10_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=962963&highlight=diaphragm)) {{:techtalk:ih:elec:delco-remy_horn_rebuild_1_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) {{:techtalk:ih:elec:delco-remy_horn_rebuild_11_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=962963&highlight=diaphragm)) \\ | ||
+ | |||
+ | A bench grinder was used to grind the rivet faces off flat. You can also use a drill bit that is larger than the hole in the rivets to drill off the face. \\ | ||
+ | Then you can use a center punch to knock the rivets out or pull them out of the other side with pliers. \\ | ||
+ | Then separate the halves and clean up all surfaces with sand paper or a wire wheel. \\ | ||
+ | |||
+ | {{:techtalk:ih:elec:delco-remy_horn_rebuild_2_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) {{:techtalk:ih:elec:delco-remy_horn_rebuild_3_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) {{:techtalk:ih:elec:delco-remy_horn_rebuild_4_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) \\ | ||
+ | |||
+ | You can check the continuity of the coil but be careful not to break the wire. \\ | ||
+ | Use some 400 grit sand paper to lightly resurface the contact points (you may have to push the lower contact down to get the sandpaper in and out). \\ | ||
+ | After everything is cleaned up, reassemble the horn and test. \\ | ||
+ | There is a small screw on the back of the horn, you can make slight turns on it to adjust the horn for the best sound. \\ | ||
+ | Keep in mind that too far one way or the other and the horn will not work at all. Use pop rivets to put the horn back together after a thin coat of RTV. \\ | ||
+ | Ensure that you don't get any sealant on the vibrating plate or it will not work. \\ | ||
+ | |||
+ | {{:techtalk:ih:elec:delco-remy_horn_rebuild_5_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) {{:techtalk:ih:elec:delco-remy_horn_rebuild_6_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) {{:techtalk:ih:elec:delco-remy_horn_rebuild_7_by_68iron.jpg?direct&300|}} ((photo by 68iron of the XLFORUM http://xlforum.net/forums/showthread.php?t=965512)) \\ | ||
\\ | \\ | ||
[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |