Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ih:engctl03 [2020/04/30 20:23] hippysmack [Sub-Documents] |
techtalk:ih:engctl03 [2021/12/11 08:24] hippysmack [Sub-Documents] |
||
---|---|---|---|
Line 6: | Line 6: | ||
===== Sub-Documents ===== | ===== Sub-Documents ===== | ||
* . . . [[techtalk:ih:engctl03a|1968 Kicker Cover Roll Pin Repair]] \\ | * . . . [[techtalk:ih:engctl03a|1968 Kicker Cover Roll Pin Repair]] \\ | ||
- | * . . . [[techtalk:ih:engctl03b|1970-1978 Kicker Cover Damage Repair]] | + | * . . . [[techtalk:ih:engctl03b|1977-1978 Kicker Cover Damage Repair]] |
* Starting July 1, 1973, there was a new design with a kick starter ratchet gear, bushing and spacer. The new 'pressed in' bushing has a Teflon coated lead bearing surface on a steel ball shell. The gear has a groove for the starter gear spring and the spacer length (and diameter) were increased to fit the new gear. ((HD Service Bulletin #618C as updated December 17, 1974)) | * Starting July 1, 1973, there was a new design with a kick starter ratchet gear, bushing and spacer. The new 'pressed in' bushing has a Teflon coated lead bearing surface on a steel ball shell. The gear has a groove for the starter gear spring and the spacer length (and diameter) were increased to fit the new gear. ((HD Service Bulletin #618C as updated December 17, 1974)) | ||
Line 36: | Line 36: | ||
Some early production 1980 models had the same plug hole and bushing for the kicker shaft as the 79 models had. ((Hapster of the XLFORUM)) \\ | Some early production 1980 models had the same plug hole and bushing for the kicker shaft as the 79 models had. ((Hapster of the XLFORUM)) \\ | ||
+ | We have confirmation of an early 1980 case with crankcase# (780 347 084), machined December 13, 1979 does have the hole for the kicker. ((OutlawTexan67 of the XLFORUM http://xlforum.net/forums/showthread.php?t=47136&page=3)) \\ | ||
Some 1980 models came with a 1979 engine with 1980 numbers that match the H9 frame - (1979). \\ | Some 1980 models came with a 1979 engine with 1980 numbers that match the H9 frame - (1979). \\ | ||
So it all depends on if you have a left over production 1979 engine installed. \\ | So it all depends on if you have a left over production 1979 engine installed. \\ | ||
Line 41: | Line 42: | ||
^Kick Start Kit|| | ^Kick Start Kit|| | ||
|1979-E1980|33058-79^ | |1979-E1980|33058-79^ | ||
+ | |||
+ | |||
+ | ---- | ||
+ | |||
+ | 1968-E1980 kicker hole plug. \\ | ||
+ | |||
+ | {{:techtalk:ih:engctl:1974_xlh_kicker_hole_plug_by_74_xlh_winchester_va.jpg?direct&300|}} ((photos by 74_XLH_WINCHESTER_VA of the XLFORUM, combined by Hippysmack, http://xlforum.net/forums/showthread.php?threadid=727978)) \\ | ||
\\ | \\ | ||
[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |