Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ih:engmech01g [2022/03/23 20:21] hippysmack [Torque Sequence] |
techtalk:ih:engmech01g [2022/10/06 21:55] hippysmack [Cam Cover Gasket] |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| ====== Cam Cover Gasket ====== | ====== Cam Cover Gasket ====== | ||
| - | [[techtalk:ih:engmech01c#upper_oil_feed_galley|Click Here]] to read more about gearcase changes around the upper feed galley. \\ | + | [[techtalk:ih:engmech01#cam_cover_gasket|Click Here]] to view a list of cam cover gaskets and more information on case changes that affected the gaskets. \\ |
| **Make sure to use the correct gasket for your engine/cover specifics**. \\ | **Make sure to use the correct gasket for your engine/cover specifics**. \\ | ||
| There were changes to the upper feed galley that dictate a specific gasket, especially between 1979-1982 models. \\ | There were changes to the upper feed galley that dictate a specific gasket, especially between 1979-1982 models. \\ | ||
| + | The upper oil feed galley was redesigned during the 1979-1982 and according to the MoCo, the gasket must fit the case design. \\ | ||
| - | **1957-E1982 right cases with the small boss and __upper oil feed oil slot__:** \\ | ||
| - | 1952-1976 K and Sportsters original gasket (25224-52), designed with an upper feed oil hole. Updated gasket (25224-52A). \\ | ||
| - | 1977-L1981 and some E1982 Sportsters original gasket (25224-52A) original had a single for the upper feed galley passage. \\ | ||
| - | The original gasket was updated in Nov. 1979 with a short slanted slot added to match the gearcase modification in L1979-E1980 models. ((TSB M-778 dated May 13, 1980)) \\ | ||
| - | And the updated -52A gasket replaced the -52 gasket for 1952-1976 models in the -78B catalog. \\ | ||
| - | |||
| - | **1982-1985 and some L1981 right cases with the large boss and __upper oil feed hole__:** \\ | ||
| - | L1981-1985 Sportsters use gasket (25263-81), designed with a long horizontal slot. \\ | ||
| - | |||
| - | | 1957-E1982 oil feed slot ((photo courtesy of Ebay seller, inlinefabrication. [[https://www.ebay.com/str/inlinefabrication|Link to Ebay Store]] )) | L1981-1985 oil feed hole ((photo courtesy of c3cycle.com, Link to site: https://www.c3cycle.com/)) | | ||
| - | |{{:techtalk:ih:engmech:1972_xlch_gearcase_oil_galley_by_inlinefabrication.jpg?direct&300|}}|{{:techtalk:ih:engmech:1984l_xls_gearcase_oil_galley_by_c3-cycle-tech.jpg?direct&300|}}| | ||
| - | |||
| - | | Cam Cover Gasket (25224-52A) ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] )) | Cam Cover Gasket (25263-81) | | ||
| - | |{{:techtalk:ih:engmech:1977-l1981_and_some_1982_sportsters_cam_cover_gasket_25224-52a_by_jrsvintageharley1990.jpg?direct&300|}}|{{:techtalk:ih:engmech:1982-1985_and_some_l1981_sportsters_cam_cover_gasket_25263-81_by_jrsvintageharley1990.jpg?direct&300|}}| | ||
| ====== Cam Cover Fastener List ====== | ====== Cam Cover Fastener List ====== | ||
| Line 106: | Line 93: | ||
| On the right menu, click on "Using a Torque Wrench" scroll down to Technique. \\ | On the right menu, click on "Using a Torque Wrench" scroll down to Technique. \\ | ||
| It's safer to use a beam type wrench on these fasteners than a clicker type wrench. \\ | It's safer to use a beam type wrench on these fasteners than a clicker type wrench. \\ | ||
| + | |||
| + | | Beam type in/lb torque wrench w/ hex adapter ((photo by Hippysmack)) | | ||
| + | |{{:techtalk:ref:tools:torque_wrench_with_hex_bit_adapters_by_hippysmack.jpg?direct&300|}}| | ||
| Below are pics with the adapted sequence shown. Use at your own discrepancy. \\ | Below are pics with the adapted sequence shown. Use at your own discrepancy. \\ | ||
