Differences

This shows you the differences between two versions of the page.

--- techtalk:ih:engmech04a [2019/06/14 17:31]
hippysmack [Cut Down]
+++ techtalk:ih:engmech04a [2019/06/14 19:23]
hippysmack [Pros and Cons of Functionality]
@@ Line 12: / Line 12: @@
 **Pros**: \\
+There really is nothing to be gained by splitting the Rocker Boxes, it's purely Cosmetic. ((hoosier xlc of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964&page=3)) \\
+It's just a matter of personal preference. But then again so is half the stuff folks do to their bikes. \\
+There is nothing different in splitting the rocker boxes than; \\
+Trimming the cam cover, drilling holes in the chain/belt guard, welding a hardtail section on a swing arm frame, \\
+Running the wires internally in the bars, a slick paint job, flat blacking everything, chroming everything, \\
+Installing 16"+ apes on HD's Sport Bike, adding a 250mm rear tire or side mounting a license plate. \\
+Some split the rocker boxes for adding dual plugged heads. The right side sparkplug is on the same angle as the left. ((fdny37 of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964&page=3)) \\
+On some other dual plug bikes, the right side plug was installed more towards the top of the head and the boxes didn't require splitting. \\
+Cometic metal rocker gaskets seem to help with leaks. \\
 If the rocker covers are doing a "hula dance" when in one full piece; ((Tim The Grim of the XLFORUM http://xlforum.net/forums/showthread.php?t=1719533&highlight=splitting+rocker+box&page=5)) \\
 Once they are split, each half is no longer reacting to the flex caused by the opposing side and is therefore more stable. \\
@@ Line 33: / Line 44: @@
 Your pushrods are doing the same thing 29 times a second at 3500 rpm. \\
 The last thing we want is to make things less rigid. \\
+The pushrods have enough trouble with harmonics without adding another place for the valve train to flex. ((mrmom9r of the XLFORUM http://xlforum.net/forums/showthread.php?t=1682099&highlight=splitting+rocker+box)) \\
+I've seen flex as high as .025" just rolling an engine with big valve springs over on the bench. \\
+If we lose up to .025" or more due to box flex, that is that much less that the valve is opening. ((Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1682099&highlight=splitting+rocker+box&page=2)) \\
+So much for your hi lift cam. \\
 Even on dead stock valve train the naked eye can actually see the pushrod end of split boxes flex when pushing the kicker thru. ((DR DICK of the XLFORUM http://xlforum.net/forums/showthread.php?t=1719533&highlight=splitting+rocker+box&page=2)) \\
@@ Line 63: / Line 79: @@
 To keep the strength of the center bolt design, you can weld up the oiling cross hole and run external lines from the outside. ((ryder rick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1998127&highlight=split+rocker+box&page=2)) \\
 That is better than splitting the boxes. \\
+To dual plug the heads, the plug electrode location is what is critical, not the angle the plug screws in from. ((ryder rick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1682099&highlight=splitting+rocker+box)) \\
+You can use a small spark plug 12mm or even 10mm. A big plug doesn't make any bigger spark. \\
+{{:techtalk:ih:engmech:dual_plugging_ihs_1_by_ryder_rick.jpg?direct&300|}} ((photo by ryder rick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1682099&highlight=splitting+rocker+box)) \\{{:techtalk:ih:engmech:dual_plugging_ihs_2_by_ryder_rick.jpg?direct&300|}} ((photo by ryder rick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1682099&highlight=splitting+rocker+box)) \\
 ====== General Process Of Splitting the Rocker Box ======
+These are Shovelhead rocker boxes but the process is about the same. ((hoosier xlc of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964)) \\
+The center portion where the front bolt goes was left on below to help give support once the pushrods are adjusted. \\
+(in an attempt to help eliminate the chance of a leak).
+First start off with a good set of boxes. Spray a little layout die on them and lay them out for a reference line. ((photos by hoosier xlc of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964)) \\
+|{{:techtalk:ih:engmech:splitting_rocker_boxes_1_by_hoosier_xlc.jpg?direct&300|}}|{{:techtalk:ih:engmech:splitting_rocker_boxes_2_by_hoosier_xlc.jpg?direct&300|}}|{{:techtalk:ih:engmech:splitting_rocker_boxes_3_by_hoosier_xlc.jpg?direct&300|}}|
+Set each box in a vice and mill down the center. Then weld up the oil passages where the split was made. \\
+And clean up the areas modified to smooth things out. ((photos by hoosier xlc of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964)) \\
+|{{:techtalk:ih:engmech:splitting_rocker_boxes_4_by_hoosier_xlc.jpg?direct&300|}}|{{:techtalk:ih:engmech:splitting_rocker_boxes_5_by_hoosier_xlc.jpg?direct&300|}}|{{:techtalk:ih:engmech:splitting_rocker_boxes_6_by_hoosier_xlc.jpg?direct&300|}}|
+Lastly, you'll need to relocate the oil passages, and decide whether or not to polish or powder coat them. ((photos by hoosier xlc of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964)) \\
+|{{:techtalk:ih:engmech:splitting_rocker_boxes_7_by_hoosier_xlc.jpg?direct&300|}}|{{:techtalk:ih:engmech:splitting_rocker_boxes_8_by_hoosier_xlc.jpg?direct&300|}}|{{:techtalk:ih:engmech:splitting_rocker_boxes_9_by_hoosier_xlc.jpg?direct&300|}}|
 ====== Cut Down ======
@@ Line 100: / Line 134: @@
 ====== Other Split Rocker Box Pics ======
-|  75 XLH ((photo by fdny37 of the XLFORUM http://xlforum.net/forums/showthread.php?t=120623))  |
+|  75 XLH ((photo by fdny37 of the XLFORUM http://xlforum.net/forums/showthread.php?t=120623)) \\ These were split for the dual plug setup. ((photo by fdny37 of the XLFORUM http://xlforum.net/forums/showthread.php?t=130964&page=2))  |
 |{{:techtalk:ih:engmech:75_xlh_w_split_rocker_boxes_by_fdny37.jpg?direct&300|}}|

Trace:

Differences

Navigation

Search

Toolbox