Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ih:engmech09 [2021/03/26 01:22] hippysmack [Rear Mounts] |
techtalk:ih:engmech09 [2021/04/20 05:57] hippysmack [1977-1985 top mounts] |
||
---|---|---|---|
Line 258: | Line 258: | ||
1982-1990 mounts offset the engine 13/32" to the left of the position for pre 1982 engines and don't have the hole in them for the kicker shaft to go through. ((billeuze of the XLFORUM http://xlforum.net/forums/showthread.php?p=5791608&highlight=motor+mount#post5791608)) \\ | 1982-1990 mounts offset the engine 13/32" to the left of the position for pre 1982 engines and don't have the hole in them for the kicker shaft to go through. ((billeuze of the XLFORUM http://xlforum.net/forums/showthread.php?p=5791608&highlight=motor+mount#post5791608)) \\ | ||
+ | |||
+ | 1984-1990 Rear Mount: \\ | ||
+ | This mount is made from billet aluminum and was also sold as a replacement for the 82-83 rear motor mount. \\ | ||
+ | |||
+ | {{:techtalk:ih:engmech:16203-82a_pic1_by_boneyard_cycles.jpg?direct&300|}} ((photo courtesy of Boneyard Cycles in Melbourne, FL)) {{:techtalk:ih:engmech:16203-82a_pic2_by_boneyard_cycles.jpg?direct&300|}} ((photo courtesy of Boneyard Cycles in Melbourne, FL)) {{:techtalk:ih:engmech:16203-82a_pic3_by_boneyard_cycles.jpg?direct&300|}} ((photo courtesy of Boneyard Cycles in Melbourne, FL)) \\ | ||
+ | |||
+ | {{:techtalk:ih:engmech:16203-82a_pic4_by_boneyard_cycles.jpg?direct&300|}} ((photo courtesy of Boneyard Cycles in Melbourne, FL)) {{:techtalk:ih:engmech:16203-82a_pic5_by_boneyard_cycles.jpg?direct&300|}} ((photo courtesy of Boneyard Cycles in Melbourne, FL)) {{:techtalk:ih:engmech:16203-82a_pic6_by_boneyard_cycles.jpg?direct&300|}} ((photo courtesy of Boneyard Cycles in Melbourne, FL)) \\ | ||
===== Broken / cracked rear mount ===== | ===== Broken / cracked rear mount ===== | ||
Line 450: | Line 457: | ||
* **1977 to 1981**: ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1644495)) ((1979-1985 HD Sportster Parts Catalog 99451-85 pg 7)) | * **1977 to 1981**: ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1644495)) ((1979-1985 HD Sportster Parts Catalog 99451-85 pg 7)) | ||
* The top front bracket (16265-76) is an "L" shaped piece with 3 mounting holes. \\ It attaches to the front two rocker cover studs (3412) and to the frame neck by a bolt (3991) that screws in upwards. \\ If the front of the frame is stock, you should see the threaded hole by looking up with a flashlight. \\ It should be a 5/16"-18 x 7/8" hex head. \\ The upper front mount can be tedious to install. Easiest to install while installing the rocker cover while things are loose. ((Ironmick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567505&page=3)) | * The top front bracket (16265-76) is an "L" shaped piece with 3 mounting holes. \\ It attaches to the front two rocker cover studs (3412) and to the frame neck by a bolt (3991) that screws in upwards. \\ If the front of the frame is stock, you should see the threaded hole by looking up with a flashlight. \\ It should be a 5/16"-18 x 7/8" hex head. \\ The upper front mount can be tedious to install. Easiest to install while installing the rocker cover while things are loose. ((Ironmick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567505&page=3)) | ||
- | * The center head straddle mount (16250-57) between the heads is black except for 79-E83 XLS which is chrome (16276-79). \\ It is not an actual motor mount but does keep structural integrity between the heads. | + | * The center head straddle mount (16250-57) between the heads is black except for 79-E83 XLS which is chrome (16276-79). \\ It is not an actual motor mount but does keep structural integrity between the heads but doesn't attach to the frame. |
* The top rear bracket (16266-76) has a hole and two open slots. \\ It attaches to the two left side rocker cover studs (3412) and to a bolt that runs thru a tube that is welded to the frame. \\ Order of install from bottom to top: rocker-washer-stud-bracket-washer-nut. ((sgr60 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567505&page=3)) \\ However, you do have to check as they sometimes need an extra washer to ensure that the weight/force of the engine is on the bracket. | * The top rear bracket (16266-76) has a hole and two open slots. \\ It attaches to the two left side rocker cover studs (3412) and to a bolt that runs thru a tube that is welded to the frame. \\ Order of install from bottom to top: rocker-washer-stud-bracket-washer-nut. ((sgr60 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567505&page=3)) \\ However, you do have to check as they sometimes need an extra washer to ensure that the weight/force of the engine is on the bracket. | ||
* **1982-E1983 XL / XLX, E83 XLS**: | * **1982-E1983 XL / XLX, E83 XLS**: |