Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ih:general02 [2017/03/22 04:43] hippysmack created |
techtalk:ih:general02 [2017/04/29 07:24] hippysmack |
||
---|---|---|---|
Line 71: | Line 71: | ||
</WRAP>| | </WRAP>| | ||
((Harley Davidson 1970 - 1977 Service Manual)) | ((Harley Davidson 1970 - 1977 Service Manual)) | ||
+ | |||
+ | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
===== Service Interval Engine and Transmission ===== | ===== Service Interval Engine and Transmission ===== | ||
Line 106: | Line 108: | ||
*Starter Motor Thru Bolt (Hitachi): 20 - 25 in-lbs / 27.11 - 33.89 Nm | *Starter Motor Thru Bolt (Hitachi): 20 - 25 in-lbs / 27.11 - 33.89 Nm | ||
+ | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
====== 1970 - 1977 Sportster Engine Specifications ====== | ====== 1970 - 1977 Sportster Engine Specifications ====== | ||
Line 200: | Line 203: | ||
- | ====== 1970 - 1977 Sportster Transmission Specifications ====== | ||
- | |||
- | ===== Clutch ===== | ||
- | *Type | ||
- | * 1970: Dry - Multiple disc | ||
- | * 1971 & later: Wet - Multiple disc | ||
- | * Capacity: 1971 & later: 1900 in-lbs. | ||
- | * Set up Spring Pressure | ||
- | * 1970: 150 lbs. | ||
- | * 1971: 234 lbs. | ||
- | * 1972: 257 lbs. | ||
- | * Spring adjustment | ||
- | * 1970: 3/16 in. from inner surface of spring tension adjusting plate to outer surface of spring cup flange | ||
- | * 1971 - 1973: 11/32 in. from outer surface of outer drive plate to outer surface of releasing disc | ||
- | * Late 1974 & later: Fixed spacers standard length 1.530 in. | ||
- | * Clutch bearing: .0005 - .002 in. loose | ||
- | * Clutch cover | ||
- | * 1970: Must be leak proof. No gasket sealer | ||
- | * Clutch release rod movement | ||
- | * 1970: .095 - .115 in. | ||
- | |||
- | ===== Chain ===== | ||
- | *Type primary: 3/8 in. pitch triple chain | ||
- | *Looseness: 5/8 to 7/8 in. slack (cold engine) - 3/8 to 5/8 in. slack (hot engine) | ||
- | |||
- | ===== Starter ===== | ||
- | * Minimum clearance between clutch teeth on starter clutch gear and clutch with starter in up position: .040 in. | ||
- | * Crankshaft endplay: .001 - .007 in. | ||
- | |||
- | ===== Chain ===== | ||
- | *Type primary: 3/8 in. pitch triple chain | ||
- | *Looseness: 5/8 to 7/8 in. slack (cold engine) - 3/8 to 5/8 in. slack (hot engine) | ||
- | ===== Mainshaft Group ===== | ||
- | |||
- | |||
- | ===== Countershaft Group ===== | ||
+ | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |