Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ih:oil02 [2019/04/24 00:36]
hippysmack [IH: Oiling & Lubrication]
techtalk:ih:oil02 [2021/02/18 01:57]
hippysmack [Primary Vent]
Line 1: Line 1:
 [[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]] [[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]]
 ====== IH: Oiling & Lubrication ====== ====== IH: Oiling & Lubrication ======
-Primary ​oil level plug / bolt. \\+====== Trans/​Primary Oiling ====== 
 +====== ​Primary ​Oil Level Plug / bolt ====== 
 57-70 (3728), 1/​4"​x20x1/​2"​ hex bolt. \\ 57-70 (3728), 1/​4"​x20x1/​2"​ hex bolt. \\
 71-85 (2420), 1/​4"​x20x3/​4"​ posidrive bolt. \\ 71-85 (2420), 1/​4"​x20x3/​4"​ posidrive bolt. \\
 Any 1/​4'​x20 bolt will do as a replacement. \\ Any 1/​4'​x20 bolt will do as a replacement. \\
-If the threads are jacked up when this bolt is removed, you can drill/tap to next size up. ((doodah man of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​p=5122516)) \\+If the threads are jacked up when this bolt is removed, you can drill / tap to next size up. ((doodah man of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​p=5122516)) \\
  
 |{{:​techtalk:​ih:​oil:​1982_oil_level_site_hole_by_yakcm2.jpg?​direct&​400|}}| |{{:​techtalk:​ih:​oil:​1982_oil_level_site_hole_by_yakcm2.jpg?​direct&​400|}}|
 |  1982 Primary Oil Site Plug ((photo by Yakcm2 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=2001239&​highlight=primary+drain+plug)) ​ | |  1982 Primary Oil Site Plug ((photo by Yakcm2 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=2001239&​highlight=primary+drain+plug)) ​ |
  
 +====== Primary Oiling ======
 +\\
 +====== Transmission / Primary Vent ======
 +1957-1976 models vent the primary thru the motor internally via the oil transfer valve. [[techtalk:​ih:​oil01#​transfer_valve_76_and_earlier|Click here]] to read more on the transfer valve in the Sportsterpedia. \\
 +1977-1985 models vent out the back of the motor from the top of the transmission near the rear motor mount just behind the solenoid (1/4” hose fitting). \\
 +
 +**Routing the vent hose**:
 +
 +  * Note: The transmission vent hose routing on Late 1981 XLH/XLS models was changed per Service Bulletin M-813 to reduce excessive oil leakage from the transmission.
 +    * Early 1981 models can be changed to the new routing.
 +    * The vent hose should be routed under the starter, over all the oil lines and the rear brake line, then down between the pivot bolt and swing arm. ((HD Service Bulletin #M-813 dated January, 30 1981)) \\
 +
 +Generally speaking, the rubber hose should run up under the seat and curl pointing down. If it has rotted or come loose from the fitting it can make a mess of that area.  ((IronMick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​p=5779702&​highlight=transmission+vent#​post5779702)) \\
  
 \\ \\
 +
 [[:​techtalk:​menu|{{:​techtalk:​gototechnicalmenu.jpg|}}]] [[:​techtalk:​menu|{{:​techtalk:​gototechnicalmenu.jpg|}}]]