Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ih:oil03 [2019/11/14 05:31] hippysmack [Oil Pump Cycle] |
techtalk:ih:oil03 [2019/12/04 00:27] hippysmack [Sub Documents] |
||
---|---|---|---|
Line 23: | Line 23: | ||
In 1972 and with the birth of the 1000cc engine, the pump numbers were -72. \\ | In 1972 and with the birth of the 1000cc engine, the pump numbers were -72. \\ | ||
It had larger gears and a bigger breather slot. \\ | It had larger gears and a bigger breather slot. \\ | ||
+ | ** | ||
+ | |||
+ | Some pump gear data from kitabel**: ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) \\ | ||
+ | The pitch distance of 14 & 16 tooth pumps is not the same. \\ | ||
+ | All driven and idler gears have .422" ID center holes. \\ | ||
+ | 14 tooth gears (1952-61) are .970" OD. \\ | ||
+ | All feed gears are .217" thick. \\ | ||
+ | All return gears are .360" thick. \\ | ||
+ | 16 tooth gears (1962-76, also all 45 & UL return pumps) are 1.115" OD. \\ | ||
+ | 1962-71 feed are .185" thick. \\ | ||
+ | 1962-71 return .375" thick. \\ | ||
+ | 1972-76 return .398" thick. \\ | ||
+ | 45 & UL 1937-73 return .315" thick. \\ | ||
+ | Inspect your spares and purchases carefully - 1936-* OHV BT gears are 14 tooth, but .990" OD and only the driven gears have .422" ID hole (the idlers are .342"). \\ | ||
+ | |||
====== XR-750 Oil Pumps (only) ====== | ====== XR-750 Oil Pumps (only) ====== | ||
* From 1972 to 1989, the gear driven oil pump went through several changes. | * From 1972 to 1989, the gear driven oil pump went through several changes. | ||
Line 113: | Line 128: | ||
* Oil is forced into a valve with a one way spring loaded cup set at 1-1/2 psi. \\ From that valve, oil exits the pump and enters the crankcase. Oil pressure is indicated by the oil pressure switch. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) | * Oil is forced into a valve with a one way spring loaded cup set at 1-1/2 psi. \\ From that valve, oil exits the pump and enters the crankcase. Oil pressure is indicated by the oil pressure switch. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) | ||
- | {{:techtalk:ih:oil:a77-_85_oil_pump_drawing_by_hippysmack.jpg?direct&400|}} ((drawing by Hippysmack)) {{:techtalk:ih:oil:77-85_oil_pump_feed_transfer_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | + | {{:techtalk:ih:oil:77-_85_oil_pump_drawing_by_hippysmack.jpg?direct&400|}} ((drawing by Hippysmack)) {{:techtalk:ih:oil:77-85_oil_pump_feed_transfer_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) |