Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
techtalk:ih:oil03 [2019/12/19 06:25] hippysmack |
techtalk:ih:oil03 [2019/12/19 06:40] hippysmack |
||
|---|---|---|---|
| Line 44: | Line 44: | ||
| * Width (?) | * Width (?) | ||
| * Driven gear: | * Driven gear: | ||
| - | * Center hole I.D. (.422") | + | * Center hole I.D. (.422") ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) |
| * Idler gear: | * Idler gear: | ||
| - | * Center hole I.D. (.422") | + | * Center hole I.D. (.422") ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) |
| * The production changes made during its run: ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * The production changes made during its run: ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
| * 57-e58 baseline pump that all others came from. \\ No oil seal. \\ Uses a snap ring and a full profile woodruff key at scavenge gear. | * 57-e58 baseline pump that all others came from. \\ No oil seal. \\ Uses a snap ring and a full profile woodruff key at scavenge gear. | ||
| Line 61: | Line 61: | ||
| * Width (?) | * Width (?) | ||
| * Driven gear: | * Driven gear: | ||
| - | * Center hole I.D. (.422") | + | * Center hole I.D. (.422") ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) |
| * Idler gear: | * Idler gear: | ||
| - | * Center hole I.D. (.422") | + | * Center hole I.D. (.422") ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) |
| * All use half moons and shortened key on scavenge drive. | * All use half moons and shortened key on scavenge drive. | ||
| * Bodies made till '66 are for style 1 plumbing. | * Bodies made till '66 are for style 1 plumbing. | ||
| Line 79: | Line 79: | ||
| * Width (?) | * Width (?) | ||
| * Driven gear: | * Driven gear: | ||
| - | * Center hole I.D. (.422") | + | * Center hole I.D. (.422") ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) |
| * Idler gear: | * Idler gear: | ||
| - | * Center hole I.D. (.422") | + | * Center hole I.D. (.422") ((kitabel of the XLFORUM http://xlforum.net/forums/showthread.php?p=5792413#post5792413)) |
| * Feed gears are the same as 57-e62 but the scavenge set is now wider again (wider than any of the previous sets). | * Feed gears are the same as 57-e62 but the scavenge set is now wider again (wider than any of the previous sets). | ||
| * Breather gear gets enlarged slots in it. ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * Breather gear gets enlarged slots in it. ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
