IH: Oiling & Lubrication - Sub-03D

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
[[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
====== IH: Oiling & Lubrication - Sub-03D ======
====== 77-85 Oil Pump Parts Lists and Upgrades ======
Originated from an article by DirtyCory of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=2071153)) ((Hippysmack of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071153&page=2)) \\
See the [[techtalk:ih:oil03#oil_pump|77-85 Oil Pump]] section of the Sportsterpedia for pics, dims and more information.

====== Pump Assembly Upgrades ======

There were 4 different pump assemblies used on Sportsters from 77-85. \\
Each one will bolt to any 77-85 engine as it's own assembly. \\ 
(and may be found at swap meets or online) \\
The only mounting difference being that you might have to change out or work around the fittings. \\
45° and 90° fittings were changed in some of the different year model pumps. \\

===== (26204-75) 1977-1981 oil pump assembly =====

Sold for use on 77-81 engines only. Last sold in 1984. \\
There were 3 different versions of this pump in regards to upgrades but the body and major internals are the same. \\
Upgrades and parts list versions created thereof are shown below. \\
The assembly has a 45° feed fitting and a 90° return fitting. \\

==== 78 Upgrades / Changes ====

  * **New parts / numbers from the -78 parts catalog**:
    * New check valve body O-ring (12042) for the '1600' pump only. \\ (to account for a possible oversized condition in the check valve bore in the 77 '1600' pump)
    * New check valve (26435-76A).
      * Both the prior and new check valves have the same lower O-ring.
  * **Discontinued for Parts Order**:
    * Original check valve (26435-76) no longer available for parts order.
    * The 1600 pump is no longer produced.
  * **Notes**:
    * 77 check valve body O-ring (26432-76) still available for standard oil pumps.
    * The Oil pressure switch (26554-77) was listed in the -77A parts supplement catalog.
      * However, it was listed as a L77 addition in the -78 parts supplement. \\ Previous models had a pressure switch. The circumstance of this switch being a late addition is unclear. \\ There was a wiring harness upgrade in 78 and oil pressure gauge available for 77-78 models.
    * Double nuts (7638) for the oil pressure switch also a late addition part #. \\ (retainer for the wire to the oil light)

==== 79 Upgrades / Changes ====

  * **Discontinued for Parts Order**:
    * O-ring (12042) no longer available for parts order.
  * **Notes**:
    * O-ring (26432-76) now the only one available.

==== 80 Upgrades / Changes ====

  * **New parts / numbers**:
    * Upgraded cover O-ring (26434-76A)
      * This O-ring replaces the original and is used in future oil pumps through 1985.
  * **Discontinued for Parts Order**:
    * Previous cover O-ring (26434-76) no longer available for parts order. 

==== 81 Upgrades / Changes ====
There were no changes to the oil pump noted in the -81 parts catalog. \\

==== 82 Upgrades / Changes ====

  * **New parts / numbers**:
    * New oil pump assembly (26204-82) for 82 only.
      * All internal components are the same part numbers from the 77-81 except for the oil line fittings.
    * The part number changed for the 4 Allen head mounting bolts (3478) although their size didn't change.
  * **Discontinued for Parts Order**:
    * Oil pump mounting bolts (1794).
  * **Notes**:
    * The 77-81 pump has a 45° fitting and a 90° return fitting.
    * The 82 pump has the 45° fitting on both the feed and return outlets.
      * This coincides with the oil tank upgrade in 82 (oil line sizes did not change).
    * 77-81 oil pump (26204-75), as upgraded, still sold for 81 and prior models (due to the fittings being different in the new assembly).


==== E83 Upgrades / Changes ====

  * **New Parts / Numbers**:
    * Upgraded pump assembly (26204-82A) for 82 and up.
    * New oil pump body (26484-83).      
    * New pump cover (26486-83).
    * New outer plate (26493-75A) for 83 year model only.
    * New outer plate seal (12036A).
  * **Discontinued for Parts Order**:
    * The 82 pump assembly (26204-82) no longer available for parts order.
    * Pump cover (26486-75) no longer available for parts order.
  * **Notes**:
    * 77-81 oil pump (26204-75), as upgraded, still sold for 81 and prior models (due to the fittings being different in the new assembly).
      * 82-E83 oil pumps have the 45° oil fittings on both the feed and return hose connections.
    * Pump body (26484-75) still available for parts order.
    * The (26486-83) replacement cover is the same as the -75 cover. \\ (and also assembled with the 45° feed fitting - old part number deleted)
    * Outer plate (26493-75) still sold for 82 and prior models.

====== Parts List per Oil Pump Assembly ======

      * The information below is a compilation of individual year catalogs plus long year span catalogs.
      * There were 2 long year span parts catalogs published for sale as the 78 catalog. Both were written years after 1978;
        * The -78A parts catalog was printed in April 1981 and reflects parts available at that time.
        * The -78B parts catalog (printed post IH era) was 'copyright 1989' and reflects parts available then. \\ (namely parts that were available in 1985 or later for the 77-85 oil pump, disregarding some - i.e. gerotors as above)        
      * 1979 and later parts catalogs only reference prior fitment back to 1979. \\ (although, many parts will fit 77-78 models)

====== 77-E83 Oil Pump Assembly ======
===== (26204-75) 77-81 =====

  * **Notes**:
    * **Retainer nuts for the oil pressure switch connector**.
      * There was no mention of the nuts on the oil pressure switch.
      * Most likely OEM on 77 models and offered for replacement parts in 78?
      * The -78A parts catalog shows them as a L77 part. ((1954-1977 HD Sportster XLH/XLCH-1000 Parts Catalog pg 23 (99451-78A) ))
    * **Gerotors**.
      * Both feed and scavenge gerotors have a chamfered radius (.020“ x 45° chamfer or .020”) on each outside gearset.
      * The same radius is designed into their respective oil pump body and cover.
      * The gerotor part numbers were used from 77-E83.
      * However, there was a TSB ((HD Technical Service Bulletin #M-711 dated June 3, 1977)) regarding the early feed gerotors.
        * The feed gerotors fit inside the oil pump cover and should extend .001” - .005“ above the ridge.
        * This bulletin also says the __later__ feed gerotors should extend up to .011” above the ridge.
      * It is unclear at this point what the difference would have been between the early and late feed gerotors by June of 1977.
      * However, the part number did not change.
    * **The special "1600" oil pump**.
      * [[sportster_history:99xx-01#section19701979|From the Sportsterpedia history section]], There was a special "1600" oil pump installed on E1000 engines. ((HD Service Letter ML-39 dated March 4, 1977))
      * This special (77 only) pump is not listed as a separate item in any of the parts catalogs or supplements.
      * It's possible this was a vendor quality control issue on their casting.
      * A quantity of them had oversized oil pump body 0-rings (which are assembled in the groove in the check valve bore to seal the pump cover).
      * This oversize 0-ring (12042) must be used in place of the standard 0-ring (26432-76) on these pumps only.
      * All such special pumps are identified with the letter "0" stamped on the pump body (exact location unknown).
      * So, the "1600" oil pump (body at least) appears to be the original casting on 77 models.
      * However, it's exact origin and demise is still unclear.

==== 77 Version ====

|Part #|Description|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|
|(7069)|Oil pressure switch lockwasher (#10) - (2)|
|(<wrap hi>7638</wrap>) \\ L77|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|
|(12036)|Outer plate seal (between the gerotors)|
|(12042) \\ 78|O-ring, body (seals the check valve in the pump body) \\  1977 - 1600 pump only  |
|(26204-75)|Oil pump assembly|
|(26430-76)|Gear shaft pin|
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|
|(26432-76)|O-ring, body (seals the check valve in the pump body)|
|(26433-77)|Lower O-ring|
|(26434-76)|Cover O-ring (between the pump halves)|
|(26435-76)|Check valve|
|(26461-77)|Spring washer (between the two plates)|
|(26463-77)|Inner plate (return gerotors sit on this plate)|
|(26480-77)|Roll pin|
|(26484-75)|Oil pump body|
|(26486-75)|Pump cover (fitted with 45° oil fitting)|
|(26488-75)|Gear shaft|
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|
|(26491-75)|Return gerotor set (thick ones)|
|(26492-75)|Feed gerotor set (thin ones)|
|(26493-75)|Outer plate (sits on top of the feed gerotors)|
|(26495-75)|Gasket (pump to engine case)|
|(26496-75)|90° Return fitting (3/8" hose nipple)|
|(26497-75)|Gear shaft retaining ring|
|(<wrap hi>26554-77</wrap>) \\ L77|Oil pressure switch|
|(63540-62)|45° feed fitting (3/8" hose nipple)|

==== 78-79 Version ====

|Part #|Description|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|
|(7069)|Oil pressure switch lockwasher (#10) - (2)|
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|
|(12036)|Outer plate seal (between the gerotors)|
|(26204-75)|Oil pump assembly|
|(26430-76)|Gear shaft pin|
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|
|(26432-76)|O-ring, body (seals the check valve in the pump body)|
|(26433-77)|Lower O-ring|
|(26434-76)|Cover O-ring (between the pump halves)|
|<wrap hi>(26435-76A)</wrap>|Check valve|
|(26461-77)|Spring washer (between the two plates)|
|(26463-77)|Inner plate (return gerotors sit on this plate)|
|(26480-77)|Roll pin|
|(26484-75)|Oil pump body|
|(26486-75)|Pump cover (fitted with 45° oil fitting)|
|(26488-75)|Gear shaft|
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|
|(26491-75)|Return gerotor set (thick ones)|
|(26492-75)|Feed gerotor set (thin ones)|
|(26493-75)|Outer plate (sits on top of the feed gerotors)|
|(26495-75)|Gasket (pump to engine case)|
|(26496-75)|90° Return fitting (3/8" hose nipple)|
|(26497-75)|Gear shaft retaining ring|
|(26554-77)|Oil pressure switch|
|(63540-62)|45° Feed fitting (3/8" hose nipple)|

==== 80-81 Version ====

|Part #|Description|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|
|(7069)|Oil pressure switch lockwasher (#10) - (2)|
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|
|(12036)|Outer plate seal (between the gerotors)|
|(26204-75)|Oil pump assembly|
|(26430-76)|Gear shaft pin|
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|
|(26432-76)|O-ring, body (seals the check valve in the pump body)|
|(26433-77)|Lower O-ring|
|(<wrap hi>26434-76A</wrap>)|Cover O-ring (between the pump halves)|
|(26435-76A)|Check valve|
|(26461-77)|Spring washer (between the two plates)|
|(26463-77)|Inner plate (return gerotors sit on this plate)|
|(26480-77)|Roll pin|
|(26484-75)|Oil pump body|
|(26486-75)|Pump cover (fitted with 45° oil fitting)|
|(26488-75)|Gear shaft|
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|
|(26491-75)|Return gerotor set (thick ones)|
|(26492-75)|Feed gerotor set (thin ones)|
|(26493-75)|Outer plate (sits on top of the feed gerotors)|
|(26495-75)|Gasket (pump to engine case)|
|(26496-75)|90° Return fitting (3/8" hose nipple)|
|(26497-75)|Gear shaft retaining ring|
|(26554-77)|Oil pressure switch|
|(63540-62)|45° Feed fitting (3/8" hose nipple)|

===== (26204-82) 82 =====
One year production assembly. \\
The assembly has a 45° feed fitting and a 45° return fitting. \\

==== 82 Version ====
|Part #|Description|
|(<wrap hi>3478</wrap>)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|
|(7069)|Oil pressure switch lockwasher (#10) - (2)|
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|
|(12036)|Outer plate seal (between the gerotors)|
|(26430-76)|Gear shaft pin|
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|
|(26432-76)|O-ring, body (seals the check valve in the pump body)|
|(26433-77)|Lower O-ring|
|(26434-76A)|Cover O-ring (between the pump halves)|
|(26435-76A)|Check valve|
|(26461-77)|Spring washer (between the two plates)|
|(26463-77)|Inner plate (return gerotors sit on this plate)|
|(26480-77)|Roll pin|
|(26484-75)|Oil pump body|
|(26486-75)|Pump cover (fitted with 45° oil fitting)|
|(26488-75)|Gear shaft|
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|
|(26491-75)|Return gerotor set (thick ones)|
|(26492-75)|Feed gerotor set (thin ones)|
|(26493-75)|Outer plate (sits on top of the feed gerotors)|
|(26495-75)|Gasket (pump to engine case)|
|(26497-75)|Gear shaft retaining ring|
|(26554-77)|Oil pressure switch|
|(<wrap hi>63540-62</wrap>)|45° feed and return fittings (3/8" hose nipple)|


===== (26204-82A) E1983 =====
Production assembly on E83 models only. \\
The assembly has a 45° feed fitting and a 45° return fitting. \\

==== E83 Version ====
|Part #|Description|
|(3478)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|
|(7069)|Oil pressure switch lockwasher (#10) - (2)|
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|
|(<wrap hi>12036A</wrap>)|Outer plate seal (between the gerotors)|
|(26430-76)|Gear shaft pin|
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|
|(26432-76)|O-ring, body (seals the check valve in the pump body)|
|(26433-77)|Lower O-ring|
|(26434-76A)|Cover O-ring (between the pump halves)|
|(26435-76A)|Check valve|
|(26461-77)|Spring washer (between the two plates)|
|(26463-77)|Inner plate (return gerotors sit on this plate)|
|(26480-77)|Roll pin|
|(<wrap hi>26484-83</wrap>)|Oil pump body|
|(<wrap hi>26486-83</wrap>)|Pump cover (fitted with 45° oil fitting)|
|(26488-75)|Gear shaft|
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|
|(26491-75)|Return gerotor set (thick ones)|
|(26492-75)|Feed gerotor set (thin ones)|
|(<wrap hi>26493-75A</wrap>)|Outer plate (sits on top of the feed gerotors)|
|(26495-75)|Gasket (pump to engine case)|
|(26497-75)|Gear shaft retaining ring|
|(26554-77)|Oil pressure switch|
|(63540-62)|45° feed and return fittings (3/8" hose nipple)|


===== (26197-83) L1983 =====
L83-85 production assembly. \\
The assembly has a 90° feed fitting and a 90° return fitting. \\
This pump first appeared in the -84 parts catalog. \\

However, it's unclear of how many of it's upgraded parts were listed in the 84 parts catalog. \\

The MoCo was still producing the 77-E83 style oil pumps for 77-81 models \\ (-84 copyright August-83, includes the E83 gerotors which were discontinued for production models by November of 1982 per the TSB). \\
The new style gerotors were not in the book but the (26197-83) part number is for the L83 pump. \\
It's upgraded parts appear in the -85 parts catalog. \\

==== L83-85 Version ====
|Part #|Description|
|(3478)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|
|(7069)|Oil pressure switch lockwasher (#10) - (2)|
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|
|(12036A)|Outer plate seal (between the gerotors)|
|(26430-76)|Gear shaft pin|
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|
|(26432-76)|O-ring, body (seals the check valve in the pump body)|
|(26433-77)|Lower O-ring|
|(26434-76A)|Cover O-ring (between the pump halves)|
|(26435-76A)|Check valve|
|(26461-77)|Spring washer (between the two plates)|
|(26463-77)|Inner plate (return gerotors sit on this plate)|
|(26480-77)|Roll pin|
|(26484-83)|Oil pump body|
|(26486-83)|Pump cover|
|(26488-75)|Gear shaft|
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|
|(26491-75)|Return gerotor set (thick ones)|
|(26492-75)|Feed gerotor set (thin ones)|
|(26493-75A)|Outer plate (sits on top of the feed gerotors)|
|(26495-75)|Gasket (pump to engine case)|
|(26496-75)|90° Return and feed fittings (3/8" hose nipple)|
|(26497-75)|Gear shaft retaining ring|
|(26554-77)|Oil pressure switch|



====== Gerotors ======
 
    * There were 2 different sets of gerotors used in Sportster oil pumps from 77-85.
      * 77-E83; Return set (26491-75), Feed set (26492-75). Discontinued for production models by November of 1982. ((HD Service Bulletin #M860 dated November 12, 1982 pg 2))
      * L83-85; Return set (26491-83), Feed set (26492-83).
    * The -78B parts book lists the original gerotors. \\ (even though that catalog was written in 1989 after the design change).

===== Late 1983 oil pump assembly design modification =====
 
  * The late 83 oil pump assembly (26197-83) gerotor gears are fabricated without the chamfered top and bottom on the outer diameters as was in the 77-E1983 gerotors. \\ This new assembly will retrofit to 77-E83 ((HD Service Bulletin #M860 dated November 12, 1982 pg 2)) ((HD Service Bulletin #M-892 dated June 22, 1984)) ((IronMick))
  * Late 1983 pump bodies and covers were also under-cut or relieved to accommodate for clearances with the new gerotors. 
  * The 77-E83 chamfered gerotors have a (.020" x 45° chamfer or .020") radius and the same radius is designed into their respective oil pump body / cover. 
  * The Late 83 pump body and cover has a (.010" max. radius) undercut for clearance designed into them.
  * These modifications limit interchangeability and affect the installation of repair parts:
    * Either early style or late style gerotor gears may be used with late style (under-cut) oil pump bodies and covers.
    * Only early style chamfered gerotor gears may be used with early style oil pump bodies and covers \\ (Use of  late style gerotor gears in early style oil pump bodies and covers could cause the oil pump to bind up and possible pump failure).


====== Oil pump check valve ======

    * The oil pump check valve had 2 different part numbers.
      * The original was (26435-76) in 1977. 
    * The part number was upgrade (26435-76A)  for L77-78 models ((1954-1977 HD Sportster XLH/XLCH-1000 Parts Catalog Supplement (99451-77A) )) ((1954-1978 HD Sportster XLH/XLCH-1000 Parts Catalog Supplement (99451-78) )) ((1954-1977 HD Sportster XLH/XLCH-1000 Parts Catalog pg 23 (99451-78A) )) 
    * Speculation could say...,
      * The original check was for the special "1600" pump (discontinued L77).
      * And the upgraded check was for installation in a newer, non publicized, pump casting not cataloged.
    * Either way, the upgraded check valve was used through 1985 on IHs.

====== Parts Lists per Catalogs ======
This is a compilation of period correct parts cataogs for 77-85 oil pumps. \\
In addition, the table to the right lists which years each part was used. \\
New part numbers in each year are highlighted. \\

Catalogs; \\

  * 99451-77A supplement catalog
  * 99451-78 supplement catalog
  * 99451-78A catalog
  * 99451-79 catalog
  * 99451-79A catalog
  * 99451-80 catalog
  * 99451-81 catalog
  * 99451-82 catalog
  * 99451-83 catalog
  * 99451-84 catalog
  * 99451-85 catalog


Some of the parts listed in the later catalogs will be different than the period correct ones. \\
These catalogs reflect parts that were available at the time of printing. \\ 
(which may be upgrades instead original parts). \\
Also, referenced were; \\

  * 99451-78B (1989)
  * 99451-85A (1990) 
===== 1977 Oil Pump =====


**Parts list from the -77A and -78 parts catalog supplements**: ((1954-1977 HD Sportster XLH/XLCH-1000 Parts Catalog Supplement (99451-77A) )) ((1954-1978 HD Sportster XLH/XLCH-1000 Parts Catalog Supplement (99451-78) )) \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  77  |  77-81  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  77  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  77  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  Late 77  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  Late 77  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  77  |  77-82  |
|<wrap hi>(12042)</wrap>|O-ring, body (seals the check valve in the pump body) \\ (from -78)|  77 only  |  77 - 1600 \\ pump only  |
|(26204-75)|Oil pump assembly|  77  |  77-81  |
|(26430-76)|Gear shaft pin|  77  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  77  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  77  |  77-84  |
|(26433-77)|Lower O-ring|  77  |  77-85  |
|(26434-76)|Cover O-ring (between the pump halves)|  77  |  77-79  |
|(26435-76)|Check valve|  77  |  77 only  |
|(26461-77)|Spring washer (between the two plates)|  77  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  77  |  77-85  |
|(26480-77)|Roll pin|  77  |  77-85  |
|(26484-75)|Oil pump body|  77  |  77-82  |
|(26486-75)|Pump cover|  77  |  77-82  |
|(26488-75)|Gear shaft|  77  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  77  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  77  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  77  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  77  |  77-82  |
|(26495-75)|Gasket (pump to engine case)|  77  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  77  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  77  |  77-85  |
|(26554-77)|Oil pressure switch (from -78)|  Late 77-78  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  77  |  77-E83  |
|:::|45° Return fitting|  (not listed)  |  82-E83  |

===== 1978 Oil Pump =====

**Parts list from the -78 parts catalog supplement**: ((1954-1978 HD Sportster XLH/XLCH-1000 Parts Catalog Supplement (99451-78) )) \\
Part # changes in the table below are highlighted. \\ 
(although HD has changed parts without changing the part numbers) \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  77-78  |  77-81  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  77-78  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  77-78  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  Late 77-78  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  Late 77-78  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  77-78  |  77-82  |
|<wrap hi>(12042)</wrap>|O-ring, body (seals the check valve in the pump body)|  77 only  |  77 - 1600 \\ pump only  |
|(26204-75)|Oil pump assembly|  77-78  |  77-81  |
|(26430-76)|Gear shaft pin|  77-78  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  77-88  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  77-78  |  77-84  |
|(26433-77)|Lower O-ring|  77-78  |  77-85  |
|(26434-76)|Cover O-ring (between the pump halves)|  77-78  |  77-79  |
|<wrap hi>(26435-76A)</wrap>|Check valve|  77-78  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  77-78  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  77-78  |  77-85  |
|(26480-77)|Roll pin|  77-78  |  77-85  |
|(26484-75)|Oil pump body|  77-78  |  77-82  |
|(26486-75)|Pump cover|  77-78  |  77-82  |
|(26488-75)|Gear shaft|  77-78  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  77-78  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  77-78  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  77-78  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  77-78  |  77-82  |
|(26495-75)|Gasket (pump to engine case)|  77-78  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  77-78  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  77-78  |  77-85  |
|(26554-77)|Oil pressure switch|  Late 77-78  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  77-78  |  77-E83  |
|:::|45° Return fitting|  (not listed)  |  82-E83  |

===== 1979 Oil Pump =====



**Parts list from the -79 parts catalog**: ((1979 HD Sportster XLH/XLCH-1000 Parts Catalog pg 15 (99451-79) )) \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79  |  77-81  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79  |  77-82  |
|(26204-75)|Oil pump assembly|  79  |  77-81  |
|(26430-76)|Gear shaft pin|  79  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  79  |  77-84  |
|(26433-77)|Lower O-ring|  79  |  77-85  |
|(26434-76)|Cover O-ring (between the pump halves)|  79  |  77-79  |
|(26435-76A)|Check valve|  79  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79  |  77-85  |
|(26480-77)|Roll pin|  79  |  77-85  |
|(26484-75)|Oil pump body|  79  |  77-82  |
|(26486-75)|Pump cover|  79  |  77-82  |
|(26488-75)|Gear shaft|  79  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  79  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  79  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  79  |  77-82  |
|(26495-75)|Gasket (pump to engine case)|  79  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  79  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79  |  77-85  |
|(26554-77)|Oil pressure switch|  79  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79  |  77-E83  |
|:::|45° Return fitting|  (not listed)  |  82-E83  |

===== 1980 Oil Pump =====

**Parts list from the -80 parts catalog**: ((1979 & 1980 HD Sportster XLH/XLCH/XLS-1000 Parts Catalog pg 15 (99451-80) )) \\
Part # changes in the table below are highlighted. \\ 

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79-80  |  77-81  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79-80  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79-80  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79-80  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79-80  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79-80  |  77-82  |
|(26204-75)|Oil pump assembly|  79-80  |  77-81  |
|(26430-76)|Gear shaft pin|  79-80  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79-80  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  79-80  |  77-84  |
|(26433-77)|Lower O-ring|  79-80  |  77-85  |
|<wrap hi>(26434-76A)</wrap>|Cover O-ring (between the pump halves)|  79-80  |  80-85  |
|(26435-76A)|Check valve|  79-80  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79-80  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79-80  |  77-85  |
|(26480-77)|Roll pin|  79-80  |  77-85  |
|(26484-75)|Oil pump body|  79-80  |  77-82  |
|(26486-75)|Pump cover|  79-80  |  77-82  |
|(26488-75)|Gear shaft|  79-80  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79-80  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  79-80  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  79-80  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  79-80  |  77-82  |
|(26495-75)|Gasket (pump to engine case)|  79-80  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  79-80  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79-80  |  77-85  |
|(26554-77)|Oil pressure switch|  79-80  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79-80  |  77-E83  |
|:::|45° Return fitting|  (not listed)  |  82-E83  |

===== 1981 Oil Pump =====

  * Notes:
    * There are no changes noted in the -81 parts catalog.


**Parts list from the -81 parts catalog**: ((1979 to 1981 HD Sportster XLH/XLCH/XLS-1000 Parts Catalog pg 17 (99451-81) )) \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(1794)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79-81  |  77-81  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79-81  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79-81  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79-81  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79-81  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79-81  |  77-82  |
|(26204-75)|Oil pump assembly|  79-81  |  77-81  |
|(26430-76)|Gear shaft pin|  79-81  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79-81  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  79-81  |  77-84  |
|(26433-77)|Lower O-ring|  79-81  |  77-85  |
|(26434-76A)|Cover O-ring (between the pump halves)|  79-81  |  80-85  |
|(26435-76A)|Check valve|  79-81  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79-81  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79-81  |  77-85  |
|(26480-77)|Roll pin|  79-81  |  77-85  |
|(26484-75)|Oil pump body|  79-81  |  77-82  |
|(26486-75)|Pump cover|  79-81  |  77-82  |
|(26488-75)|Gear shaft|  79-81  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79-81  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  79-81  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  79-81  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  79-81  |  77-82  |
|(26495-75)|Gasket (pump to engine case)|  79-81  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  79-81  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79-81  |  77-85  |
|(26554-77)|Oil pressure switch|  79-81  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79-81  |  77-E83  |
|:::|45° Return fitting|  (not listed)  |  82-E83  |

===== 1982 Oil Pump =====

**Parts list from the -82 parts catalog**: ((1979 to 1982 HD XL Models Parts Catalog pg 19 (99451-82) )) \\
Part # changes in the table below are highlighted. \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(3478)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79-82  |  82-85  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79-82  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79-82  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79-82  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79-82  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79-82  |  77-82  |
|(26204-75)|Oil pump assembly|  79-81  |  77-81  |
| <wrap hi>(26204-82)</wrap> |Oil pump assembly|  82  |  82 only  |
|(26430-76)|Gear shaft pin|  79-82  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79-82  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  79-82  |  77-84  |
|(26433-77)|Lower O-ring|  79-82  |  77-85  |
|(26434-76A)|Cover O-ring (between the pump halves)|  79-82  |  80-85  |
|(26435-76A)|Check valve|  79-82  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79-82  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79-82  |  77-85  |
|(26480-77)|Roll pin|  79-82  |  77-85  |
|(26484-75)|Oil pump body|  79-82  |  77-82  |
|(26486-75)|Pump cover|  79-82  |  77-82  |
|(26488-75)|Gear shaft|  79-82  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79-82  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  79-82  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  79-82  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  79-82  |  77-82  |
|(26495-75)|Gasket (pump to engine case)|  79-82  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  79-81  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79-82  |  77-85  |
|(26554-77)|Oil pressure switch|  79-82  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79-82  |  77-E83  |
|:::|45° Return fitting|  82  |  82-E83  |

 

===== 1983 Oil Pump =====

**Parts list from the -83 parts catalog**: ((1979 to 1983 HD XL Models Parts Catalog pg 19 (99451-83) )) \\
Part # changes in the table below are highlighted. \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(3478)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79-83  |  82-85  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79-83  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79-83  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79-83  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79-83  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79-82  |  77-82  |
|(<wrap hi>12036A</wrap>)|Outer plate seal (between the gerotors)|  83  |  83-85  |
|(26204-75)|Oil pump assembly|  79-81  |  77-81  |
| <wrap hi>(26204-82A)</wrap> |Oil pump assembly|  82-83  |  83 only  |
|(26430-76)|Gear shaft pin|  79-83  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79-83  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  79-83  |  77-84  |
|(26433-77)|Lower O-ring|  79-83  |  77-85  |
|(26434-76A)|Cover O-ring (between the pump halves)|  79-83  |  80-85  |
|(26435-76A)|Check valve|  79-83  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79-83  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79-83  |  77-85  |
|(26480-77)|Roll pin|  79-83  |  77-85  |
|(26484-75)|Oil pump body|  79-82  |  77-82  |
|(<wrap hi>26484-83</wrap>)|Oil pump body|  83  |  83-84  |
|(26486-75)|Pump cover|  79-83  |  77-82  |
|(<wrap hi>26486-83</wrap>)|Pump cover|  83  |  83-84  |
|(26488-75)|Gear shaft|  79-83  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79-83  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  79-83  |  77-E83  |
|(26492-75)|Feed gerotor set (thin ones)|  79-83  |  77-E83  |
|(26493-75)|Outer plate (sits on top of the feed gerotors)|  79-82  |  77-82  |
|(<wrap hi>26493-75A</wrap>)|Outer plate (sits on top of the feed gerotors)|  83  |  83-85  |
|(26495-75)|Gasket (pump to engine case)|  79-83  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|  79-81  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  (not listed)  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79-83  |  77-85  |
|(26554-77)|Oil pressure switch|  79-83  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79-83  |  77-E83  |
|:::|45° Return fitting|  82-83  |  82-E83  |



===== 1984 Oil Pump =====

  * **New Parts / Numbers**:
    * New oil pump assembly (26197-83) for L83 models (listed as a 'Pump Kit' in the -78B parts catalog). ((HD XL Models Parts Catalog pg 23 (99451-78B) ))
      * All other internals are the same as in 83 (according to the 84 catalog).
      * However, the 85 catalog and a service bulletin revealed the true internal changes to this new pump.
      * The new pump assembly will retrofit to 77-E83 ((HD Service Bulletin #M860 dated November 12, 1982 pg 2, HD Service Bulletin #M-892 dated June 22, 1984))
      * These modifications limit interchangeability and affect the installation of repair parts:
      * Either early style or late style gerotor gears may be used with late style (under-cut) oil pump bodies and covers.
      * Only early style chamfered gerotor gears may be used with early style oil pump bodies and covers. \\ (Use of late style gerotor gears in early style oil pump bodies and covers could cause the oil pump to bind up and possible pump failure).
  * **Discontinued for Parts Order**:
    * Oil pump assembly (26204-82A) no longer available for parts order. 
  * **Notes**:
    * Oil pump assembly (26204-75) still sold for 81 and prior models.

**Parts list from the -84 parts catalog**: ((1979 to 1984 HD XL Models Parts Catalog pg 21 (99451-84) )) \\
Part # changes in the table below are highlighted. \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(3478)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79-84  |  82-85  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79-84  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79-84  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79-84  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79-84  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79-82  |  77-82  |
|(12036A)|Outer plate seal (between the gerotors)|  79-84  |  83-85  |
|(<wrap hi>26197-83</wrap>)|Oil pump assembly|  82-84  |  82-85  |
|(26204-75)|Oil pump assembly|  79-81  |  77-81  |
|(26430-76)|Gear shaft pin|  79-84  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79-84  |  77-85  |
|(26432-76)|O-ring, body (seals the check valve in the pump body)|  79-84  |  77-84  |
|(26433-77)|Lower O-ring|  79-84  |  77-85  |
|(26434-76A)|Cover O-ring (between the pump halves)|  79-84  |  80-85  |
|(26435-76A)|Check valve|  79-84  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79-84  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79-84  |  77-85  |
|(26480-77)|Roll pin|  79-84  |  77-85  |
|(26484-75)|Oil pump body|  79-82  |  77-82  |
|(26484-83)|Oil pump body|  83-84  |  83-84  |
|(26486-75)|Pump cover|  79-82  |  77-82  |
|(26486-83)|Pump cover|  83-84  |  83-84  |
|(26488-75)|Gear shaft|  79-84  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79-84  |  77-85  |
|(26491-75)|Return gerotor set (thick ones)|  79-84  |  77-E-83  |
|(26492-75)|Feed gerotor set (thin ones)|  79-84  |  77-E83  |
|(26493-75A)|Outer plate (sits on top of the feed gerotors)|  79-84  |  83-85  |
|(26495-75)|Gasket (pump to engine case)|  79-84  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|    79-81 \\ L83-84  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  L83-84  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79-84  |  77-85  |
|(26554-77)|Oil pressure switch|  79-84  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79-E83  |  77-E83   |
|:::|45° Return fitting|:::|  82-E83  |
===== 1985 Oil Pump =====

  * **New Parts / Numbers**:
    * Upgraded body O-ring (26432-76A)
    * Upgraded oil pump body (26484-75A)
    * Upgraded pump cover (26486-75A)
    * New gerotors (L83-85 for the 26197-83) available for parts order:
      * (26491-83) return, set - new part# for 82-85
      * (26492-83) feed, set - new part# for 82-85
      * The new gerotor gears are fabricated without the chamfered top and bottom on the outer diameters as was in the 77-E1983 gerotors.
  * **Discontinued for Parts Order**:
    * Old pump (26204-75) no longer available for parts order.
    * Oil pump body (26484-83) no longer available for parts order.
    * Pump Cover (26486-83) no longer available for parts order.
    * Old gerotor set (26492-75) and (26491-75) no longer available
  * **Notes**:
    * Oil pump assembly (26197-83) now being sold for 85 and prior year models. \\ (as well as the individual upgraded parts along the way with the exception of the gerotors)

**Parts list from the -85 parts catalog**: ((1979 to 1985 HD XL Models Parts Catalog pg 21 (99451-85) )) \\
Part # changes in the table below are highlighted. \\

|Part #|Description|Listed for Year(s)|Factory Installed On Year(s)|
|(3478)|Oil pump mounting bolt (1/4"x20x2/12" Allen head) - (4)|  79-85  |  82-85  |
|(6242W)|Oil pump mounting bolt washer (1/4"x9/16"x1/32") - (4)|  79-85  |  77-85  |
|(7036)|Oil pump mounting bolt lockwasher (1/4") - (4)|  79-85  |  77-85  |
|(7069)|Oil pressure switch lockwasher (#10) - (2)|  79-85  |  77-85  |
|(7638)|Oil pressure nut (10-32x1/8"x3/8" hex)- (2)|  79-85  |  77-85  |
|(12036)|Outer plate seal (between the gerotors)|  79-82  |  77-82  |
|(12036A)|Outer plate seal (between the gerotors)|  83-85  |  83-85  |
|(26197-83)|Oil pump assembly|  79-85  |  82-85  |
|(26430-76)|Gear shaft pin|  79-85  |  77-85  |
|(26431-76)|Pump cover bushing (AKA lower shaft bushing)|  79-85  |  77-85  |
|(<wrap hi>26432-76A</wrap>)|O-ring, body (seals the check valve in the pump body)|  79-85  |  85  |
|(26433-77)|Lower O-ring|  79-85  |  77-85  |
|(26434-76A)|Cover O-ring (between the pump halves)|  79-85  |  80-85  |
|(26435-76A)|Check valve|  79-85  |  77-85  |
|(26461-77)|Spring washer (between the two plates)|  79-85  |  77-85  |
|(26463-77)|Inner plate (return gerotors sit on this plate)|  79-85  |  77-85  |
|(26480-77)|Roll pin|  79-85  |  77-85  |
|(<wrap hi>26484-75A</wrap>)|Oil pump body|  79-85  |  L83-85  |
|(<wrap hi>26486-75A</wrap>)|Pump cover|  79-85  |  L83-85  |
|(26488-75)|Gear shaft|  79-85  |  77-85  |
|(26489-75)|Pump body bushing (AKA upper shaft bushing)|  79-85  |  77-85  |
|(<wrap hi>26491-83</wrap>)|Return gerotor set|  82-85  |  L83-85  |
|(<wrap hi>26492-83</wrap>)|Feed gerotor set|  82-85  |  L83-85  |
|(26493-75A)|Outer plate (sits on top of the feed gerotors)|  79-85  |  83-85  |
|(26495-75)|Gasket (pump to engine case)|  79-85  |  77-85  |
|(26496-75)|90° Return fitting (3/8" hose nipple)|    79-81 \\ L83-85  |  77-81 \\ L83-85  |
|:::|90° Feed fitting|  L83-85  |  L83-85  |
|(26497-75)|Gear shaft retaining ring|  79-85  |  77-85  |
|(26554-77)|Oil pressure switch|  79-85  |  77-85  |
|(63540-62)|45° Feed fitting (3/8" hose nipple)|  79-E83  |  77-E83   |
|:::|45° Return fitting|:::|  82-E83  |






\\


[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]
Trace: • Sportster Technical Menu • REF: Tools & Fasteners • IH: Engine Mechanicals • IH: Carburetor, Intake Manifold & Exhaust - Sub-01P • EVO: Engine Control • IH: Carburetor, Intake Manifold & Exhaust - Sub-01R • IH: Carburetor, Intake Manifold & Exhaust - Sub-01Q • EVO: Engine Mechanicals • IH: Engine Mechanicals • EVO: Engine Control