Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
techtalk:ih:oil03e [2018/12/21 06:11] hippysmack [Disassembly] |
techtalk:ih:oil03e [2018/12/21 06:42] hippysmack [Disassembly] |
||
|---|---|---|---|
| Line 104: | Line 104: | ||
| |{{:techtalk:ih:oil:77-e83_oil_pump_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:outer_plate_installed_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-85_oil_pump_spring_washer_installed_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ih:oil:77-e83_oil_pump_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:outer_plate_installed_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-85_oil_pump_spring_washer_installed_by_hippysmack.jpg?direct&300|}}| | ||
| - | * Check the position and condition of the outer plate seal before removing it. | + | * **The 77-82 outer plate seal is simply pushed down the gearshaft and onto the inner plate**. |
| + | * Check the position and condition of the seal before removing it. | ||
| * Remove the seal and the retaining (lock) ring. | * Remove the seal and the retaining (lock) ring. | ||
| * You can use external lock rings pliers or a small screwdriver or two. | * You can use external lock rings pliers or a small screwdriver or two. | ||
| Line 111: | Line 112: | ||
| |{{:techtalk:ih:oil:outer_seal_installed_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-85_oil_pump_retaining_ring_location_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_4_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ih:oil:outer_seal_installed_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-85_oil_pump_retaining_ring_location_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_4_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| + | * **The 83-90 outer plate seal is pressed into the outer plate**. | ||
| + | * Check the position and condition of the seal before removing it. | ||
| + | * The seal will need to be pressed or pried out. | ||
| + | * You can set up a rig as in below (bearing race, a small socket and a rubber hammer). | ||
| + | * Make sure the socket is slightly smaller than the outer plate I.D. | ||
| + | * Gently tap the socket. | ||
| + | * And the seal will fall thru the bearing race (or larger socket etc). | ||
| + | |||
| + | |{{:techtalk:evo:oil:83-90_outer_plate_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:83-90_outer_plate_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:83-90_outer_plate_5_by_hippysmack.jpg?direct&300|}}| | ||
| * Two small drivers were used here (1 to keep the ring from spinning, 1 to raise an end out of the groove in the gearshaft). | * Two small drivers were used here (1 to keep the ring from spinning, 1 to raise an end out of the groove in the gearshaft). | ||
