Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ih:oil03e [2018/12/21 19:15] hippysmack [Stuck Cover Gasket] |
techtalk:ih:oil03e [2019/01/09 01:43] ixl2relax ↷ Links adapted because of a move operation |
||
|---|---|---|---|
| Line 64: | Line 64: | ||
| | Carburetor Cleaner ((photo by Hippysmack http://xlforum.net/forums/showthread.php?t=2071153&page=4)) ||| | | Carburetor Cleaner ((photo by Hippysmack http://xlforum.net/forums/showthread.php?t=2071153&page=4)) ||| | ||
| - | |{{:techtalk:ref:tools:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:parts_cleaner_6_by_hippysmack.jpg?direct&300|}}| | + | |{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:parts_cleaner_6_by_hippysmack.jpg?direct&300|}}| |
| * After soaking, open the lid, remove the small bucket inside by the handle, set the bucket on the ground and wash the parts cleaner off with a water hose. | * After soaking, open the lid, remove the small bucket inside by the handle, set the bucket on the ground and wash the parts cleaner off with a water hose. | ||
| Line 73: | Line 73: | ||
| | Cleaning and soaking gaskets for more easy removal ((photos by Hippysmack http://xlforum.net/forums/showthread.php?t=2071153&page=4)) || | | Cleaning and soaking gaskets for more easy removal ((photos by Hippysmack http://xlforum.net/forums/showthread.php?t=2071153&page=4)) || | ||
| - | |{{:techtalk:ref:tools:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}| | + | |{{techtalk:ref:genmsr:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}| |
| |{{:techtalk:ih:oil:77-e83_oil_pump_5.2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_5.3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_5.1_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ih:oil:77-e83_oil_pump_5.2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_5.3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_5.1_by_hippysmack.jpg?direct&300|}}| | ||
| Line 124: | Line 124: | ||
| * Two small drivers were used here (1 to keep the ring from spinning, 1 to raise an end out of the groove in the gearshaft). | * Two small drivers were used here (1 to keep the ring from spinning, 1 to raise an end out of the groove in the gearshaft). | ||
| - | * The 1st screwdriver can be pushed into the slot in the gerotor to keep the ring from spinning. | + | * The 1st screwdriver can be pushed into the slot in the gerotor to keep the ring from spinning. |
| - | * This will allow you to pick and out on one end and then switch back and forth between the two from there. | + | * This will allow you to pick and out on one end and then switch back and forth between the two from there. |
| + | * Remove the retainer clip. | ||
| + | * Then pull out the inner plate. | ||
| |{{:techtalk:ih:oil:77-e83_oil_pump_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_6_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ih:oil:77-e83_oil_pump_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ih:oil:77-e83_oil_pump_6_by_hippysmack.jpg?direct&300|}}| | ||
