Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ih:oil03f [2019/12/21 20:23]
hippysmack [Check Ball]
techtalk:ih:oil03f [2021/02/17 23:51]
hippysmack [Rear Feed Nipple or Plug]
Line 2: Line 2:
 ====== IH: Oiling & Lubrication - Sub-03F ====== ====== IH: Oiling & Lubrication - Sub-03F ======
 ====== 57-76 Oil Pump - Individual Parts and Pics ====== ====== 57-76 Oil Pump - Individual Parts and Pics ======
 +===== Sub Documents =====
 +  * [[techtalk:​ref:​engmech04k|Breather Valves (1957-Up)]] (list of breather valve changes)
 +  * [[techtalk:​ref:​engmech07g|Further Study of the Timed Breather Valve]]
  
-====== Oil Check Valve ======+====== Oil Check Ball and Spring ​====== 
 +See also [[techtalk:​ih:​oil03g#​check_ball_seat_repair|Check ball seat repair]] in the IH Oil Pump section of the Sportsterpedia. \\
  
-The oil pump check valve is in the front of the oil pumpIt's a spring and a steel ball set up. \\+The oil pump check ball is in the front of the oil pumpIt's a spring and a steel ball set up. \\
 The red area in the pic below is the spring & ball sit. \\ The red area in the pic below is the spring & ball sit. \\
  
 +Used until mid 1958, the tail of check fits inside the hollow center guide bore of the fitting. ((photo by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1347614&​page=2)) \\
 +Note that there is no inner face seal surface on the fitting to further isolate the pressure switch port from the '​backside'​ of the check. \\
  
 {{:​techtalk:​ih:​oil:​57-76_oil_pump_check_valve_location_by_ironheadjunkie_annotated_by_hippysmack.jpg?​direct&​300|}} ((photo by ironheadjunkie of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1490437)) \\ {{:​techtalk:​ih:​oil:​57-76_oil_pump_check_valve_location_by_ironheadjunkie_annotated_by_hippysmack.jpg?​direct&​300|}} ((photo by ironheadjunkie of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1490437)) \\
  
- 
-===== Check Ball ===== 
-See also [[techtalk:​ih:​oil03g#​check_ball_seat_repair|Check ball seat repair]] in the IH Oil Pump section of the Sportsterpedia. \\ 
- 
-Used until mid 1958, the tail of check fits inside the hollow center guide bore of the fitting. ((photo by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1347614&​page=2)) \\ 
-Note that there is no inner face seal surface on the fitting to further isolate the pressure switch port from the '​backside'​ of the check. \\ 
 {{:​techtalk:​ih:​oil:​oil_pump_check_spring_by_dr_dick.jpg?​direct&​300|}} {{:​techtalk:​ih:​oil:​oil_pump_check_ball_57-58_sportster_by_dr_dick.jpg?​direct&​300|}} \\ {{:​techtalk:​ih:​oil:​oil_pump_check_spring_by_dr_dick.jpg?​direct&​300|}} {{:​techtalk:​ih:​oil:​oil_pump_check_ball_57-58_sportster_by_dr_dick.jpg?​direct&​300|}} \\
  
-====== Check Spring ====== 
 There were 3 springs used from 52-76. ((Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356&​page=2)) \\ There were 3 springs used from 52-76. ((Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356&​page=2)) \\
 (52-56 also used a second valve- pressure relief). \\ (52-56 also used a second valve- pressure relief). \\
Line 39: Line 38:
 |{{:​techtalk:​ih:​oil:​oil_pump_check_spring_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​oil_pump_check_springs_by_fergerburger.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​oil_pump_check_springs_by_the_doctor71.jpg?​direct&​300|}}| |{{:​techtalk:​ih:​oil:​oil_pump_check_spring_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​oil_pump_check_springs_by_fergerburger.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​oil_pump_check_springs_by_the_doctor71.jpg?​direct&​300|}}|
 |  52-E57 ((photo by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356&​page=2)) ​ |  (L) L57-E72 - (R) L72-76 ((photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356)) ​ |  (Bottom) L57-E72 - (Top) L72-76 ((photo by The Doctor71 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356)) ​ | |  52-E57 ((photo by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356&​page=2)) ​ |  (L) L57-E72 - (R) L72-76 ((photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356)) ​ |  (Bottom) L57-E72 - (Top) L72-76 ((photo by The Doctor71 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1661356)) ​ |
 +
 +====== Rear Feed Nipple or Plug ======
 +
 +Starting in 1967, the oil feed from the tank was plumbed directly into the oil pump on the rear side on XLH motors. \\
 +The feed from the tank stayed plumbed to the top of the rear case on XLCH motors thru 1969. \\
 +In 1970, the feed on XLCH motors was now plumbed to the oil pump as well. The feed nipple (63533-41) is a 1/​8"​-27 x 3/8" Bose barb fitting. \\
 +
 +Using the same pump for both XLH and XLCH, this required a pipe plug installed there for XLCH motors from 1967-1969. \\
 +The plug is a 1/​8"​-27 NPT pipe plug. 2 part numbers were used and both are interchangeable. \\
 +Part# (45831-48) used from 1967-1968 while part# (45830-48) used in 1969. \\
 +1952-1956 K models also had a feed line plug there in the parts book part# (26424-52). \\
 +
 +|  Oil pump on 1967 XLCH w/ plug ((photo by ss396 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1864035&​page=4)) ​ |
 +|{{:​techtalk:​ih:​oil:​1967_xlch_oil_pump_1_by_ss396.jpg?​direct&​300|}}|
 ====== Breather Gears ====== ====== Breather Gears ======
  
Line 46: Line 59:
 |{{:​techtalk:​ih:​oil:​breather_gears_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​breather_gears_2_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​breather_gears_3_by_dr_dick.jpg?​direct&​300|}}| |{{:​techtalk:​ih:​oil:​breather_gears_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​breather_gears_2_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​breather_gears_3_by_dr_dick.jpg?​direct&​300|}}|
  
-|The 2 different breather housings((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|Feed Gear Sets((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|More often than not the solid pin was a slipfit in cross hole.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))| +|The 2 different breather housings((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|Feed Gear Sets((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))
-|{{:​techtalk:​ih:​oil:​breather_housings_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​feed_gear_sets_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​roll_pin-solid_pin_sets_by_dr_dick.jpg?​direct&​400|}}|+|{{:​techtalk:​ih:​oil:​breather_housings_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​feed_gear_sets_by_dr_dick.jpg?​direct&​300|}}| 
 + 
 +|More often than not the solid pin was a slipfit in cross hole.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))| 
 +|{{:​techtalk:​ih:​oil:​roll_pin-solid_pin_sets_by_dr_dick.jpg?​direct&​300|}}|
  
 |On to the bodies. The 2nd text is "​26217-56a L58-e62"​((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|| |On to the bodies. The 2nd text is "​26217-56a L58-e62"​((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))||
-|{{:​techtalk:​ih:​oil:​oil_pump2-2_by_dr_dick.jpg?​direct&​400|}}|{{:​techtalk:​ih:​oil:​oil_pump2-2-_by_dr_dick.jpg?​direct&​300|}}|+|{{:​techtalk:​ih:​oil:​oil_pump2-2_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​oil_pump2-2-_by_dr_dick.jpg?​direct&​200|}}|
  
 |The 4 different scavenge gear sets. \\ Lined up from early in foreground to later in background. \\ This is to show the height progression.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|Top view of all 4 sets.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|A closer view of the height changes.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))| |The 4 different scavenge gear sets. \\ Lined up from early in foreground to later in background. \\ This is to show the height progression.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|Top view of all 4 sets.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|A closer view of the height changes.((photos by Dr Dick of the XLFORUM http://​xlforum.net/​forums/​showpost.php?​p=3272806&​postcount=204))|
-|{{:​techtalk:​ih:​oil:​scavaenge_gear_sets_1_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​scavaenge_gear_sets_2_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​scavaenge_gear_sets_3_by_dr_dick.jpg?​direct&​300|}}| +|{{:​techtalk:​ih:​oil:​scavaenge_gear_sets_1_by_dr_dick.jpg?​direct&​220|}}|{{:​techtalk:​ih:​oil:​scavaenge_gear_sets_2_by_dr_dick.jpg?​direct&​300|}}|{{:​techtalk:​ih:​oil:​scavaenge_gear_sets_3_by_dr_dick.jpg?​direct&​300|}}|
- +
- +
- +
  
 \\ \\
- 
  
 [[:​techtalk:​menu|{{:​techtalk:​gototechnicalmenu.jpg|}}]] [[:​techtalk:​menu|{{:​techtalk:​gototechnicalmenu.jpg|}}]]