Differences

This shows you the differences between two versions of the page.

--- techtalk:ih:oil04b [2018/12/16 03:47]
hippysmack [Copper Lines for Ext Filter (75 XL)]
+++ techtalk:ih:oil04b [2018/12/18 20:16]
hippysmack [Running Copper Oil Lines]
@@ Line 2: / Line 2: @@
 ====== IH: Oiling & Lubrication - Sub-04B ======
 ===== Running Copper Oil Lines =====
+|  Copper oil lines ((photos by zman69 of the XLFORUM http://xlforum.net/forums/showthread.php?t=29406))  ||  Copper behind the chain ((photo by Jtrapass of the XLFORUM http://xlforum.net/forums/showthread.php?t=360592&page=2))  |
+|{{:techtalk:ih:oil:copper_oil_lines_2_by_zman69.jpg?direct&300|}}|{{:techtalk:ih:oil:copper_oil_lines_1_by_zman69.jpg?direct&300|}}|{{:techtalk:ih:oil:copper_oil_lines_by_jtrapass.jpg?direct&300|}}|
+|  Copper oil and gas lines ((photos by calabeast of the XLFORUM http://xlforum.net/forums/showthread.php?t=719598))  ||
+|{{:techtalk:ih:oil:copper_oil_and_gas_lines_1_by_calabeast.jpg?direct&300|}}|{{:techtalk:ih:oil:copper_oil_and_gas_lines_2_by_calabeast.jpg?direct&300|}}|
 ===== Copper Lines for Ext Filter (75 XL) =====
@@ Line 7: / Line 13: @@
 The oil return fitting is on top of the case beside the vent, not in front of the pump. \\
-So there's no easy way to route the lines toward the front for a filter. \\
+So there's no easy way to route the lines for a filter. \\
 The return needs to run down and forward to the oil filter and back to the tank. \\
 (in addition to the vent line and the oil feed to the pump) \\
@@ Line 40: / Line 46: @@
 |{{:techtalk:ih:oil:running_copper_oil_lines_4_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_5_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_6_by_sifty.jpg?direct&300|}}|
+  - The ends were double flared for strength and a solid connection to the flexible hose sections. \\ This is the first pass on the flaring tool.
+  - The second pic shows the finished double flare.
+  - In the third, the tubing is bent and ends prepped.
+|1|2|3|
 |{{:techtalk:ih:oil:running_copper_oil_lines_7_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_8_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_9_by_sifty.jpg?direct&300|}}|
+  - Adhesive lined heat shrink was installed around the copper tubing for protection and vibration damping. \\ They'll also be snugged down with cable ties so they shouldn't rub against any moving parts.
+  - Thin walled feed line (for max clearance) runs straight down and along the frame rail and tied the lower hoses where appropriate. \\ Heavy duty hydraulic hose for the lower sections to the filter to avoid any of the ties crimping the hose and to offer more mechanical protection.
+|1|2||
 |{{:techtalk:ih:oil:running_copper_oil_lines_10_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_11_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_12_by_sifty.jpg?direct&300|}}|

Trace:

Differences

Navigation

Search

Toolbox