Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:ih:oil04b [2018/12/16 03:14] hippysmack [Copper Lines for Ext Filter (75 XL)] |
— (current) | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== IH: Oiling & Lubrication - Sub-04B ====== | ||
- | ===== Running Copper Oil Lines ===== | ||
- | ===== Copper Lines for Ext Filter (75 XL) ===== | ||
- | Article by sifty of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1592463&page=30)) \\ | ||
- | |||
- | The oil return fitting is on top of the case beside the vent, not in front of the pump. \\ | ||
- | So there's no easy way to route the lines toward the front for a filter. \\ | ||
- | The return needs to run down and forward to the oil filter and back to the tank. \\ | ||
- | (in addition to the vent line and the oil feed to the pump) \\ | ||
- | |||
- | The oil tank mounting bracket has a large grommet in it. \\ | ||
- | The hole was enlarged to help cut down kinks while passing 3 lines through it. \\ | ||
- | The hole was filed out to a rounded rectangular shape and a large round grommet was cut down fit the new hole. \\ | ||
- | |||
- | Because of tight space, short sections of copper tubing were used in place of thick rubber hose. \\ | ||
- | A short piece of rubber was placed at each end of the copper lines. \\ | ||
- | The ID of the copper tubing is slightly smaller than the desired 3/8” so it isn’t ideal. \\ | ||
- | But it avoids any 'squishing' of the rubber lines. \\ | ||
- | And is probably still may be better than the 90 degree elbow joint at the output connection. | ||
- | |||
- | The copper is refrigeration tube which is soft drawn and in a coil and doesn't need annealing. \\ | ||
- | Copper work-hardens easily however. \\ | ||
- | A tubing bender was used for the bends in small increments with care not to make too tight a bend. \\ | ||
- | The only problems were with double bends that the former couldn't get around. \\ | ||
- | The tube tended to flatten out or kink when trying to bend by hand. \\ | ||
- | |||
- | |{{:techtalk:ih:oil:running_copper_oil_lines_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_3_by_sifty.jpg?direct&300|}}| | ||
- | |||
- | |{{:techtalk:ih:oil:running_copper_oil_lines_4_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_5_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_6_by_sifty.jpg?direct&300|}}| | ||
- | |||
- | |{{:techtalk:ih:oil:running_copper_oil_lines_7_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_8_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_9_by_sifty.jpg?direct&300|}}| | ||
- | |||
- | |{{:techtalk:ih:oil:running_copper_oil_lines_10_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_11_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:oil:running_copper_oil_lines_12_by_sifty.jpg?direct&300|}}| | ||
- | |||
- | |||
- | |||
- | \\ | ||
- | |||
- | |||
- | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |