Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
techtalk:ih:wheels01 [2018/02/10 14:26] hippysmack [Sub-Documents] |
techtalk:ih:wheels01 [2018/04/17 22:48] ixl2relax |
||
|---|---|---|---|
| Line 54: | Line 54: | ||
| ===== Rear Wheel Hub Internal Parts ===== | ===== Rear Wheel Hub Internal Parts ===== | ||
| - | {{:techtalk:ih:wheels:71_xlch_rear_wheel_internals_by_the_doctor71.jpg?direct&600|}} ((1971 rear wheel hub components by The Doctor71 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?postid=5643997#post5643997)) | + | {{:techtalk:ih:wheels:71_xlch_rear_wheel_internals_by_the_doctor71.jpg?direct&600|}} ((1971 rear wheel hub components by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?postid=5643997#post5643997)) |
| ====== Axles & Wheel Bearings ===== | ====== Axles & Wheel Bearings ===== | ||
| Line 121: | Line 121: | ||
| |{{:techtalk:ih:wheels:1973_front_axle_drawing_complete_by_flying_monkey.jpg?direct&300|}}| | |{{:techtalk:ih:wheels:1973_front_axle_drawing_complete_by_flying_monkey.jpg?direct&300|}}| | ||
| - | |Drawing by Flying Monkey of the XLFORUM ((http://xlforum.net/vbportal/forums/showthread.php?t=1457354&highlight=front+hub+spacers&page=2))| | + | |Drawing by Flying Monkey of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1457354&highlight=front+hub+spacers&page=2))| |
| Line 170: | Line 170: | ||
| ===== Measuring / Sizing Wheel Hub Spacers ===== | ===== Measuring / Sizing Wheel Hub Spacers ===== | ||
| - | * If your unsure of which hub spacer you need , the best way to find out is to mock up your wheel / hub and do some measuring: ((rivethog of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=1638639&page=2)) | + | * If your unsure of which hub spacer you need , the best way to find out is to mock up your wheel / hub and do some measuring: ((rivethog of the XLFORUM http://xlforum.net/forums/showthread.php?t=1638639&page=2)) |
| - Install outer races into the hub, make sure they're fully seated. Don't install any seals yet. | - Install outer races into the hub, make sure they're fully seated. Don't install any seals yet. | ||
| - Clamp the axle in a vise vertically, threaded end up. | - Clamp the axle in a vise vertically, threaded end up. | ||
| Line 199: | Line 199: | ||
| - | * On 1963-1978 XLH/XLCH Models, a bearing spacer washer HD part #41195-63 (or V-Twin part number 44-0395 ((Icefire of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=1533577&highlight=size+rear+wheel+spacer+washer&page=2))) is placed between the two bearings on the right hub (brake side). This spacer washer is reportedly not installed at the factory but is a service part for alignment where the aluminum back plate butts to the bearing inner race due to wear. The race will plow right into the soft back plate when the axle flexes ((Dr Dick http://xlforum.net/vbportal/forums/showthread.php?t=1844782)). | + | * On 1963-1978 XLH/XLCH Models, a bearing spacer washer HD part #41195-63 (or V-Twin part number 44-0395 ((Icefire of the XLFORUM http://xlforum.net/forums/showthread.php?t=1533577&highlight=size+rear+wheel+spacer+washer&page=2))) is placed between the two bearings on the right hub (brake side). This spacer washer is reportedly not installed at the factory but is a service part for alignment where the aluminum back plate butts to the bearing inner race due to wear. The race will plow right into the soft back plate when the axle flexes ((Dr Dick http://xlforum.net/forums/showthread.php?t=1844782)). |
| * This is not a grease shield for the bearing. The grease shield used on the brake side →'62 was no longer in use by '63 and up models. | * This is not a grease shield for the bearing. The grease shield used on the brake side →'62 was no longer in use by '63 and up models. | ||
| - | * This small washer has a lip, its very thin, and is not a regular flat washer. It goes in between the right side bearings in the hub, and pushes/holds the outer bearing flush with the hub where it goes up against the inside of the brake backing plate. Others have also said it is OK to use a second one in between the backing pate and the outer bearing if you need a little clearance so the backing plate wont rub, but if you need more than those 2, you should look inside your hub for issues... ((Icefire of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=1533577&highlight=size+rear+wheel+spacer+washer&page=2)) | + | * This small washer has a lip, its very thin, and is not a regular flat washer. It goes in between the right side bearings in the hub, and pushes/holds the outer bearing flush with the hub where it goes up against the inside of the brake backing plate. Others have also said it is OK to use a second one in between the backing pate and the outer bearing if you need a little clearance so the backing plate wont rub, but if you need more than those 2, you should look inside your hub for issues... ((Icefire of the XLFORUM http://xlforum.net/forums/showthread.php?t=1533577&highlight=size+rear+wheel+spacer+washer&page=2)) |
| |{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_1_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_2_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_5_by_dirtyharry68.jpg?direct&300|}}| | |{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_1_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_2_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_5_by_dirtyharry68.jpg?direct&300|}}| | ||
| - | | Rear Wheel Bearing Spacer Washer (brake side) ((photos by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=2047584&page=3)) || App. Dims: ID -.737", OD - 1.008" (((Doc o of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=1533577)), width .012" ((DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=2047584&page=3)) | | + | | Rear Wheel Bearing Spacer Washer (brake side) ((photos by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2047584&page=3)) || App. Dims: ID -.737", OD - 1.008" (((Doc o of the XLFORUM http://xlforum.net/forums/showthread.php?t=1533577)), width .012" ((DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2047584&page=3)) | |
| |{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_3_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_4_by_dirtyharry68.jpg?direct&300|}}| | |{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_3_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ih:wheels:rear_wheel_bearing_spacer_washer_-_brake_side_4_by_dirtyharry68.jpg?direct&300|}}| | ||
| - | | As it sits on the open bearing ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=2047584&page=3)) | As it sits (more loosely) on the sealed bearing. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=2047584&page=3)) | | + | | As it sits on the open bearing ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2047584&page=3)) | As it sits (more loosely) on the sealed bearing. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2047584&page=3)) | |
| Line 427: | Line 427: | ||
| | |18" Rear|4.0 x 18|18 psi||||| | | |18" Rear|4.0 x 18|18 psi||||| | ||
| ^1970-1978 ((1970-1978 HD Sportster Parts Catalog pg 1-1))^Wheel Size and Position^Wheel Type^Rim Contour^Tire Size (Goodyear or Yokohama) \\ Use corresponding size inner tubes^^^Recommended \\ Tire Pressure^ | ^1970-1978 ((1970-1978 HD Sportster Parts Catalog pg 1-1))^Wheel Size and Position^Wheel Type^Rim Contour^Tire Size (Goodyear or Yokohama) \\ Use corresponding size inner tubes^^^Recommended \\ Tire Pressure^ | ||
| - | |XLH-XLCH-XLT|19" Front|Cast, 7 or 9 spoke| T 19 2.15 TL ((Mike02king from the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=2010145))|MJ90-19 * (XLT use Yokohama Y-980 only)|||| | + | |XLH-XLCH-XLT|19" Front|Cast, 7 or 9 spoke| T 19 2.15 TL ((Mike02king from the XLFORUM http://xlforum.net/forums/showthread.php?t=2010145))|MJ90-19 * (XLT use Yokohama Y-980 only)|||| |
| |XLH-XLCH-XLT|19" Front|Laced| |3.75-19T or MM90-19((The Doctor71 of the XLFORUM)) (Taper base bead tire size, use on taper base bead rim only)((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))|||18 psi((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))| | |XLH-XLCH-XLT|19" Front|Laced| |3.75-19T or MM90-19((The Doctor71 of the XLFORUM)) (Taper base bead tire size, use on taper base bead rim only)((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))|||18 psi((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))| | ||
| - | |XLH-XLCH-XLT|18" Rear|Cast, 7 or 9 spoke|T 18 2.50 TL ((Mike02king from the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?t=2010145)) |<del>MN90-18</del> Tire obsolete, acceptable replacement 120/90-18 * (XLT use Yokohama Y-622 only)|||| | + | |XLH-XLCH-XLT|18" Rear|Cast, 7 or 9 spoke|T 18 2.50 TL ((Mike02king from the XLFORUM http://xlforum.net/forums/showthread.php?t=2010145)) |<del>MN90-18</del> Tire obsolete, acceptable replacement 120/90-18 * (XLT use Yokohama Y-622 only)|||| |
| |XLH/XLCH/XLT|18" Rear|Laced| |4.25-18T (Taper base bead tire size, use on taper base bead rim only)((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))|||30 psi((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))| | |XLH/XLCH/XLT|18" Rear|Laced| |4.25-18T (Taper base bead tire size, use on taper base bead rim only)((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))|||30 psi((HD Shop Dope Service Bulletin No 516A update from Oct 15, 1966))| | ||
| |XLH-XLCH|16" Rear (accessory)|Cast 7 spoke| |MT90-16 / 5.00-16T / 5.10-16T|||| | |XLH-XLCH|16" Rear (accessory)|Cast 7 spoke| |MT90-16 / 5.00-16T / 5.10-16T|||| | ||
