Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ih:wheels01a [2017/11/22 20:54] hippysmack created |
techtalk:ih:wheels01a [2018/04/18 01:18] ixl2relax |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
+ | ====== IH: Wheels, Brakes & Tires - Sub-01A ====== | ||
+ | |||
+ | |||
==== Problems Associated with Drum Brake Rear Hubs ==== | ==== Problems Associated with Drum Brake Rear Hubs ==== | ||
- | Article by Dr Dick of the XLFORUM ((http://xlforum.net/vbportal/forums/showthread.php?t=1525902)) | + | Article by Dr Dick of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1525902)) |
Line 9: | Line 13: | ||
* All bearings referred to below are the right side. | * All bearings referred to below are the right side. | ||
- | * 1952-1954 models: | + | |
+ | **1952-1954 ↓ models:** | ||
* Used the asymmetric flange hub (smaller spoke flange on left side). | * Used the asymmetric flange hub (smaller spoke flange on left side). | ||
* Torrington needle bearing (9011). | * Torrington needle bearing (9011). | ||
Line 15: | Line 21: | ||
* This shield is same design as the swingarm Timken shields. | * This shield is same design as the swingarm Timken shields. | ||
- | * 1955-E1958 models: | + | **1955-E1958 ↓ models:** |
+ | |||
* Used the 1st symmetric flange hub. | * Used the 1st symmetric flange hub. | ||
* No bearing change. | * No bearing change. | ||
* Used the grease shield assembly between right bearing and brake backing plate. | * Used the grease shield assembly between right bearing and brake backing plate. | ||
- | * L1958-1962 models: | + | **L1958-1962 ↓ models:** |
+ | |||
* Same hub as previously used. | * Same hub as previously used. | ||
* U the double row 'duplex' ball bearing (9010). | * U the double row 'duplex' ball bearing (9010). | ||
Line 26: | Line 36: | ||
* Used the grease shield assembly between right bearing and brake backing plate. | * Used the grease shield assembly between right bearing and brake backing plate. | ||
- | * 1963-1965 models: | + | **1963-1965 ↓ models:** |
+ | |||
* Same hub as previous. | * Same hub as previous. | ||
* Used two separate single bearings (9008) & (9009) stacked up. | * Used two separate single bearings (9008) & (9009) stacked up. | ||
* Grease shield is no longer used. | * Grease shield is no longer used. | ||
- | * 1966-1972 models: | + | **1966-1972 ↓ models:** |
+ | |||
* The brake side hub flange was made thicker at the bolt mounting area. | * The brake side hub flange was made thicker at the bolt mounting area. | ||
* Longer drum lugs were used. | * Longer drum lugs were used. | ||
* No bearing change. | * No bearing change. | ||
- | * 1973-1978 models: | + | **1973-1978 ↓ models:** |
+ | |||
* Some time between 1973 & 1975, brazing got replaced by welded construction. | * Some time between 1973 & 1975, brazing got replaced by welded construction. | ||
* No bearing change. | * No bearing change. | ||
Line 52: | Line 68: | ||
| | ||
| | ||
- | * Regarding bearing issues. | + | * **Regarding bearing issues.** |
* The most common of all hub complaints is the outer right side bearing being loose in the hub. This is very common on '66→ hubs but not as common '63-'65 and non existent on → '62. | * The most common of all hub complaints is the outer right side bearing being loose in the hub. This is very common on '66→ hubs but not as common '63-'65 and non existent on → '62. | ||
* This loose bearing is never a problem in itself. It won't leave you stranded. | * This loose bearing is never a problem in itself. It won't leave you stranded. | ||
Line 72: | Line 88: | ||
- | ---- | + | \\ |
+ | |||
+ | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||