Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:body01 [2019/06/28 23:14] hippysmack [Aftermarket Fuel Tanks] |
techtalk:ref:body01 [2022/03/09 05:15] ixl2relax ↷ Page name changed from techtalk:ref:body05 to techtalk:ref:body01 |
||
|---|---|---|---|
| Line 21: | Line 21: | ||
| ====== Petcock (Fuel Outlet) ====== | ====== Petcock (Fuel Outlet) ====== | ||
| - | When removing a factory vacuum operated petcock and swapping to a non-vacuum one, run a new (fresh) vacuum line from the carburetor to the Voes or Map Sensor (respective to year model) and discard the "tee" fitting. It will be cleaner to not use the "Y". ((V of the XLFORUM http://xlforum.net/forums/showthread.php?t=1757206&highlight=oil+pump+drive+gear+removal&page=2)) | + | When removing a factory vacuum operated petcock and swapping to a non-vacuum one, run a new (fresh) vacuum line from the carburetor to the Voes or Map Sensor (respective to year model) and discard the "tee" fitting. It will be cleaner to not use the "T". ((V of the XLFORUM http://xlforum.net/forums/showthread.php?t=1757206)) |
| + | |||
| + | Here's an XLForum thread showing several aftermarket petcocks: | ||
| + | http://xlforum.net/forums/showthread.php?t=1378389 | ||
| + | |||
| ===== Golan Petcock ===== | ===== Golan Petcock ===== | ||
| - | |{{:techtalk:ref:body:golan_brass_petcock_by_folkie.jpg?direct&400|}}|{{:techtalk:ref:body:golan_petcock_by_fourcams.jpg?direct&400|}}| | + | |{{:techtalk:ref:body:golan_brass_petcock_by_folkie.jpg?direct&300|}}|{{:techtalk:ref:body:golan_petcock_by_fourcams.jpg?direct&200|}}| |
| |Golan brass petcock. With the nut screwed all the way down, it's \\ 1-5/16" from the top of the nut to the \\ bottom of the petcock. From the bottom of the nut it's 7/8".((photo by Folkie of the XLFORUM http://xlforum.net/forums/showthread.php?t=475189))| Golan petcock installed ((photo by FourCams of the XLFORUM http://xlforum.net/forums/showthread.php?t=475189&page=2)) | | |Golan brass petcock. With the nut screwed all the way down, it's \\ 1-5/16" from the top of the nut to the \\ bottom of the petcock. From the bottom of the nut it's 7/8".((photo by Folkie of the XLFORUM http://xlforum.net/forums/showthread.php?t=475189))| Golan petcock installed ((photo by FourCams of the XLFORUM http://xlforum.net/forums/showthread.php?t=475189&page=2)) | | ||
| + | ===== Pingel Petcock ===== | ||
| + | The EFI petcock has both an inlet for the fuel pressure regulator return line and a 5/16" outlet. \\ | ||
| + | (but no strainer or reserve/shutoff valve for the EFI system) \\ | ||
| + | |||
| + | |{{:techtalk:ref:body:pingel_petcocks_by_donchicago48.jpg?direct&300|}}| | ||
| + | |5/16" with vacuum shutoff (Left), 5/16" EFI (Right) ((photo by DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=4))| | ||
| ===== 86-03 Tank Mount Mod ===== | ===== 86-03 Tank Mount Mod ===== | ||
| You can use slices of 5/16" or 3/8" ID rubber oil or fuel line to create to insulate the fuel tank from the frame in absence of the stock rubber grommets. | You can use slices of 5/16" or 3/8" ID rubber oil or fuel line to create to insulate the fuel tank from the frame in absence of the stock rubber grommets. | ||
| - | {{:techtalk:ref:body:home_made_rubber_bushings_for_gas_tank_mounts_by_ironmick.jpg?direct&600|}} ((photo by Ironmick of the XLFORUM http://xlforum.net/forums/showthread.php?t=2004980&highlight=gas+tank)) | + | {{:techtalk:ref:body:home_made_rubber_bushings_for_gas_tank_mounts_by_ironmick.jpg?direct&300|}} ((photo by Ironmick of the XLFORUM http://xlforum.net/forums/showthread.php?t=2004980&highlight=gas+tank)) |
