Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:body06 [2019/06/28 16:22] hippysmack [Fuel Tank Cleaning, Restoration and Mods] |
techtalk:ref:body06 [2022/03/09 05:22] ixl2relax ↷ Page name changed from techtalk:ref:body02 to techtalk:ref:body06 |
||
---|---|---|---|
Line 20: | Line 20: | ||
|{{:techtalk:ref:body:removing_tank_rust_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_3_by_sifty.jpg?direct&300|}}| | |{{:techtalk:ref:body:removing_tank_rust_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_3_by_sifty.jpg?direct&300|}}| | ||
+ | ====== Pulling a Dent Out ====== | ||
+ | Here is one way to pull and repair a dented gas tank. \\ | ||
+ | Grind the paint off. Make a standoff and glue it to the dented area with high strength adhesive (Hysol used below). \\ | ||
+ | Let it dry overnight or as the directions permit. Then use a slide hammer to pull the dent out. \\ | ||
+ | Carefully remove the adhesive and standoff. \\ | ||
+ | |||
+ | {{:techtalk:ref:body:repairing_gas_tank_dent_1_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_2_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_3_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) \\ | ||
+ | |||
+ | It will probably still require a small amount of body-filler to fill in the remaining imperfections. \\ | ||
+ | You can see the body-filler and primer layers in the first pic below. The entire tank has been wet-sanded with 600 grit. \\ | ||
+ | The second pic below, there are a few base coats applied. \\ | ||
+ | The filler material may require a primer to hide it during base coat. Then apply the finish coat and clear coat. \\ | ||
+ | |||
+ | {{:techtalk:ref:body:repairing_gas_tank_dent_4_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_5_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_6_by_uncledaddy.jpg?direct&250|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) \\ | ||
\\ | \\ | ||
[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||