Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:body06 [2019/06/28 16:03] hippysmack |
techtalk:ref:body06 [2022/03/09 05:22] ixl2relax ↷ Page name changed from techtalk:ref:body02 to techtalk:ref:body06 |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== REF: Body Parts ====== | ====== REF: Body Parts ====== | ||
| - | ====== Fuel Tank Cleaning, Restoration and Mods ====== | + | ====== Fuel Tank Cleaning, Restoration ====== |
| ====== Removing Internal Rust ====== | ====== Removing Internal Rust ====== | ||
| Cleaning out the loose rust scale in the fuel tank can be done with loose metal material placed inside the tank and then shaken up. \\ | Cleaning out the loose rust scale in the fuel tank can be done with loose metal material placed inside the tank and then shaken up. \\ | ||
| Line 20: | Line 20: | ||
| |{{:techtalk:ref:body:removing_tank_rust_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_3_by_sifty.jpg?direct&300|}}| | |{{:techtalk:ref:body:removing_tank_rust_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:body:removing_tank_rust_3_by_sifty.jpg?direct&300|}}| | ||
| - | ====== Adding an External Fuel Level Sight Hose / Tube ====== | + | ====== Pulling a Dent Out ====== |
| + | Here is one way to pull and repair a dented gas tank. \\ | ||
| + | Grind the paint off. Make a standoff and glue it to the dented area with high strength adhesive (Hysol used below). \\ | ||
| + | Let it dry overnight or as the directions permit. Then use a slide hammer to pull the dent out. \\ | ||
| + | Carefully remove the adhesive and standoff. \\ | ||
| + | {{:techtalk:ref:body:repairing_gas_tank_dent_1_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_2_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_3_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) \\ | ||
| + | It will probably still require a small amount of body-filler to fill in the remaining imperfections. \\ | ||
| + | You can see the body-filler and primer layers in the first pic below. The entire tank has been wet-sanded with 600 grit. \\ | ||
| + | The second pic below, there are a few base coats applied. \\ | ||
| + | The filler material may require a primer to hide it during base coat. Then apply the finish coat and clear coat. \\ | ||
| + | |||
| + | {{:techtalk:ref:body:repairing_gas_tank_dent_4_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_5_by_uncledaddy.jpg?direct&300|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) {{:techtalk:ref:body:repairing_gas_tank_dent_6_by_uncledaddy.jpg?direct&250|}} ((photo by Uncledaddy of the XLFORUM http://xlforum.net/forums/showthread.php?t=43715&page=9)) \\ | ||
| \\ | \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
