Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
techtalk:ref:body20 [2017/12/04 10:10]
techtalk:ref:body20 [2024/01/09 17:24] (current)
hippysmack
Line 1: Line 1:
 +[[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]]
 +====== REF: Body Parts ======
  
 +====== Aftermarket Handlebars, Risers and Mods ======
 +
 +====== Handlebars ======
 +
 +  * Harley-Davidson has a downloadable PDF catalog of various handlebar options, recently updated in 2020 - https://​serviceinfo.harley-davidson.com/​sip/​service/​document/​original/​1420463678980971765/​2020_sep_24_hbars.pdf
 +
 +  * For those who are shopping around for different types of bars (with their measurements),​ this section will show an approximate view from the seat and the side of how the different bars look while installed. Looks can be deceiving however with different models, color backgrounds and perceptions.
 +  ​
 +|{{techtalk:​ref:​body:​drag_bars_by_kcsporty.jpg?​direct&​300|}} {{techtalk:​ref:​body:​drag_bars-2_by_kcsporty.jpg?​direct&​300|}}|
 +|1" Drag Bars w/ stock risers and cables on a 2014 XL1200C -  30" wide, 6" pullback, 8" center. ((photo courtesy of kcsporty of the XLFORUM))|
 +
 +|{{techtalk:​ref:​body:​ape_hangers_by_brad_1.jpg?​direct&​200|}} {{techtalk:​ref:​body:​ape_hangers_by_brad_2.jpg?​direct&​300|}}|
 +|1" Ape Hangers ((http://​www.bikerparts-superstore.com/​handlebars/​ape-hangers/​chrome-15-inch-ape-hangers-handlebar-for-1982-up-harley)) w/ stock risers on a 2005 XL883C \\ Dims: 33" wide, 15" total rise, 13" rise to grip tip, 14.5" pullback, 10" center width. ((photos courtesy of Brad of the XLFORUM https://​www.xlforum.net/​forum/​sportster-motorcycle-forum/​sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/​171430-not-apes-or-drags#​post3656731))|
 +
 +|{{techtalk:​ref:​body:​moto_bar_1_by_brad.jpg?​direct&​300|}} {{techtalk:​ref:​body:​moto_bar_2_by_brad.jpg?​direct&​300|}}|
 +|1" (black) Moto Bar ((https://​www.biltwellinc.com/​p181/​buy/​parts-amp-accessories/​handlebars/​moto/​-moto-handlebars-1-quot-black/#​specs)) w/ stock risers and cables on a 2005 XL883 \\ Dims: 31" wide, 4.25" rise, 2.75" pullback, 4.75" center width. ((photos courtesy of Brad of the XLFORUM https://​www.xlforum.net/​forum/​sportster-motorcycle-forum/​sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/​171430-not-apes-or-drags#​post3656731))|
 +
 +
 +====== Risers ======
 +===== Riser Mods =====
 +==== Spacers ====
 +
 +|Done on a 2005 1200R \\  Using 3/4" sockets: a 1/​2"​x13 nut (3/4" hex) was epoxied in each socket. The threads were then drilled out to 1/2". ((photos by thunderpaw of the XLFORUM https://​www.xlforum.net/​forum/​sportster-motorcycle-forum/​sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/​50568-son-of-xena-mod?​postid=1239036#​post1053555))|||
 +|{{:​techtalk:​ref:​body:​riser_extensions_4_by_thunderpaw.jpg?​direct&​300|}}|{{:​techtalk:​ref:​body:​riser_extensions_2_by_thunderpaw.jpg?​direct&​300|}}|{{:​techtalk:​ref:​body:​riser_extensions_3_by_thunderpaw.jpg?​direct&​300|}}|
 +
 +==== Offset Riser Blocks ====
 +{{:​techtalk:​ref:​body:​offset_riser_mod_7_by_tobiism.jpg?​direct&​300|}} ((photo by tobiism of the XLFORUM https://​www.xlforum.net/​forum/​sportster-motorcycle-forum/​sportster-motorcycle-styles/​cafe-racer-sportster-motorcycle-talk/​103339-my-new-1200s-project/​page23?​t=906049&​page=23))
 +
 +|Start with some square stock aluminum, drill holes for the bars (7/8" / 1" etc.) and mark center on the outside edge to cut a pinch slot. ((photos by tobiism of the XLFORUM https://​www.xlforum.net/​forum/​sportster-motorcycle-forum/​sportster-motorcycle-styles/​cafe-racer-sportster-motorcycle-talk/​103339-my-new-1200s-project/​page22?​t=906049&​page=22))|||
 +|{{:​techtalk:​ref:​body:​offset_riser_mod_1_by_tobiism.jpg?​direct&​300|}}|{{:​techtalk:​ref:​body:​offset_riser_mod_2_by_tobiism.jpg?​direct&​300|}}|{{:​techtalk:​ref:​body:​offset_riser_mod_3_by_tobiism.jpg?​direct&​300|}}|
 +
 +|The pinch slot can be cut with a hacksaw. \\ Drill the hole for the pinch bolt, countersink that for a cap head bolt. \\ Drill and countersink the second hole for the mounting bolt to the upper tree. ((photos by tobiism of the XLFORUM https://​www.xlforum.net/​forum/​sportster-motorcycle-forum/​sportster-motorcycle-styles/​cafe-racer-sportster-motorcycle-talk/​103339-my-new-1200s-project/​page22?​t=906049&​page=22))||| ​
 +|{{:​techtalk:​ref:​body:​offset_riser_mod_4_by_tobiism.jpg?​direct&​300|}}|{{:​techtalk:​ref:​body:​offset_riser_mod_5_by_tobiism.jpg?​direct&​300|}}|{{:​techtalk:​ref:​body:​offset_riser_mod_6_by_tobiism.jpg?​direct&​300|}}|
 +
 +
 +\\
 +[[:​techtalk:​menu|{{:​techtalk:​gototechnicalmenu.jpg|}}]]