Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:body30i [2019/07/03 01:59] hippysmack [Extended Forward Controls] |
techtalk:ref:body30i [2022/03/09 04:53] ixl2relax ↷ Page name changed from techtalk:ref:body01i to techtalk:ref:body30i |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== REF: Body Parts - Sub-01I ====== | ====== REF: Body Parts - Sub-01I ====== | ||
\\ | \\ | ||
- | ====== Extended Forward Controls ====== | + | |
+ | ====== Homemade Forward Extensions ====== | ||
+ | ===== Using a Fabbed Extension Plate ====== | ||
+ | This mod gained about 4" forward and about 1.5" out to side. \\ | ||
+ | A longer stainless steel rod was threaded to link to the longer controls. \\ | ||
|2 brackets were fabricated. ((photo by Tedeburn of the XLFORUM http://xlforum.net/forums/showthread.php?t=29357))|Then the OEM brackets were bolted on. ((photo by Tedeburn of the XLFORUM http://xlforum.net/forums/showthread.php?t=29357))|Finished assembly. ((photo by Tedeburn of the XLFORUM http://xlforum.net/forums/showthread.php?t=29357))| | |2 brackets were fabricated. ((photo by Tedeburn of the XLFORUM http://xlforum.net/forums/showthread.php?t=29357))|Then the OEM brackets were bolted on. ((photo by Tedeburn of the XLFORUM http://xlforum.net/forums/showthread.php?t=29357))|Finished assembly. ((photo by Tedeburn of the XLFORUM http://xlforum.net/forums/showthread.php?t=29357))| | ||
|{{:techtalk:ref:body:homemade_forward_extensions_1_by_tedeburn.png?direct&300|}}|{{:techtalk:ref:body:homemade_forward_extensions_2_by_tedeburn.png?direct&300|}}|{{:techtalk:ref:body:homemade_forward_extensions_3_by_tedeburn.png?direct&300|}}| | |{{:techtalk:ref:body:homemade_forward_extensions_1_by_tedeburn.png?direct&300|}}|{{:techtalk:ref:body:homemade_forward_extensions_2_by_tedeburn.png?direct&300|}}|{{:techtalk:ref:body:homemade_forward_extensions_3_by_tedeburn.png?direct&300|}}| | ||
- | \\ | + | ===== Modding Dyna Highway Peg Brackets ===== |
- | ===== Homemade Forward Extensions ===== | + | In order to accomplish this mod, you need to have pipes that do not obstruct the front frame area. ((Paulie420 of the XLFORUM http://xlforum.net/forums/showthread.php?t=39020&highlight=forward+controls)) \\ |
+ | There is a 3" extension piece on either side of the frame connected at the original foot peg position. \\ | ||
+ | Then, there is a horizontal piece welded in between those two extensions for strength. \\ | ||
+ | This solves two things; putting the controls 3" out and 1/4" - 1/2" up. \\ | ||
+ | |||
+ | Then, you have to deal with the brake bar. \\ | ||
+ | Since the pegs are now 3" forward, it won't fit or the brake pedal would be underneath the peg. \\ | ||
+ | The one below was cut and 3" of steel was welded in the middle then heat wrap was installed over the whole bar. \\ | ||
+ | |||
+ | On the shifter side, a long chrome bar was cut to length and re-threaded for a linkage. ((photos by Paulie420 of the XLFORUM http://xlforum.net/forums/showthread.php?t=39020&highlight=forward+controls)) \\ | ||
+ | |{{:techtalk:ref:body:extended_forwards_1_by_paulie420.jpg?direct&300|}}| | ||
+ | |{{:techtalk:ref:body:extended_forwards_2_by_paulie420.jpg?direct&300|}}|{{:techtalk:ref:body:extended_forwards_3_by_paulie420.jpg?direct&300|}}|{{:techtalk:ref:body:extended_forwards_4_by_paulie420.jpg?direct&300|}}| | ||
====== 03 and Prior Models ====== | ====== 03 and Prior Models ====== | ||
===== JayBrake ===== | ===== JayBrake ===== |