Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
techtalk:ref:body30k [2019/06/29 16:09] hippysmack [Homemade Heel / Toe Shifter] |
techtalk:ref:body30k [2024/01/09 21:19] (current) hippysmack |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| - | ====== REF: Body Parts - Sub-01K ====== | + | ====== REF: Body Parts - Sub-30K ====== |
| \\ | \\ | ||
| ====== Shifter Mods ====== | ====== Shifter Mods ====== | ||
| ====== Pegs ====== | ====== Pegs ====== | ||
| - | 50bmg shifter: \\ | + | |50bmg shifter: The shoulder of the casing was cut off with a bolt epoxied into it. ((photos by DaytonaSportster of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-photos-videos/120968-lets-see-the-brass/page3?t=1182952&page=3))|| |
| - | The shoulder of the casing was cut off with a bolt epoxied into it. ((photos by DaytonaSportster of the XLFORUM http://xlforum.net/forums/showthread.php?t=1182952&page=3)) \\ | + | |{{:techtalk:ref:body:shifter_ped_mod_1_by_daytonasportster.png?direct&250|}}|{{:techtalk:ref:body:shifter_ped_mod_2_by_daytonasportster.png?direct&250|}}| |
| - | |{{:techtalk:ref:body:shifter_ped_mod_1_by_daytonasportster.png?direct&300|}}|{{:techtalk:ref:body:shifter_ped_mod_2_by_daytonasportster.png?direct&300|}}| | + | |Skateboard wheel mounted to the shift lever. ((photo by jonv of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-general-discussion-and-problems/199305-primary-oil-leaking-from-primary-case#post4386657))| |
| + | |{{:techtalk:ref:body:skateboard_wheel_on_shifter_lever_by_jonv.jpg?direct&300|}}| | ||
| ====== Heel / Toe Shifter ====== | ====== Heel / Toe Shifter ====== | ||
| + | |Hand Built Heel / Toe Shifter ((photo by Jolly Rogers of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-photos-videos/69053-close-ups/page53?t=461674&page=53))| | ||
| + | |{{:techtalk:ref:body:hand_built_heel_toe_shifter_by_jolly_rogers.jpg?direct&250|}}| | ||
| + | |||
| ===== Homemade Heel / Toe Shifter ===== | ===== Homemade Heel / Toe Shifter ===== | ||
| - | Article by rasaine of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=716217)) \\ | + | Article by rasaine of the XLFORUM ((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-accessories/89297-custom-made-heel-toe-shifter?t=716217)) \\ |
| These were built for a 2009 1200C. \\ | These were built for a 2009 1200C. \\ | ||
| You may have to do some measurements and fitting on different year models but the concept is the same. \\ | You may have to do some measurements and fitting on different year models but the concept is the same. \\ | ||
| + | |||
| + | |||
| + | This design will not work on the Mid Controls as there is no connecting rod. \\ | ||
| + | Mid mount controls have a shift lever that mounts directly on the splined shaft coming out of the transmission housing. \\ | ||
| + | However, you may be able to study, measure and come up with a design. \\ | ||
| Below are 2 different versions of heel / toe shifters for forward controls homemade by rasaine. \\ | Below are 2 different versions of heel / toe shifters for forward controls homemade by rasaine. \\ | ||
| Line 28: | Line 37: | ||
| **Download the full instructional PDF here**: {{ :techtalk:ref:body:homemade_heel-toe_shifter_instructions_by_rasaine.pdf |}} \\ | **Download the full instructional PDF here**: {{ :techtalk:ref:body:homemade_heel-toe_shifter_instructions_by_rasaine.pdf |}} \\ | ||
| + | These instructions are valid only for Forward controls on a 2004 – 2009 (2010??) Sportster. \\ | ||
| + | The unit I made for Terp84Alum required some modification and redesign due to the different footrest shaft used on the non-rubber mount bikes. \\ | ||
| + | Unfortunately when I converted the drawing to a PDF file, the templates do not print out true to size. \\ | ||
| + | They are close, but will need to be enlarged slightly to be accurate. \\ | ||
| + | The Shift Peg Rail is 8-1/2" end to end. \\ | ||
| + | The printed measurements are correct. \\ | ||
| **Tools**: \\ | **Tools**: \\ | ||
| Line 60: | Line 75: | ||
| The bolt ends slightly stuck out from the outside spacer, I cut them off flush with a Dremel cut-off wheel. \\ | The bolt ends slightly stuck out from the outside spacer, I cut them off flush with a Dremel cut-off wheel. \\ | ||
| Then I drilled Lightening holes. \\ | Then I drilled Lightening holes. \\ | ||
| - | Finally everything was sanded with 220 wet sand, then polished. ((photos by rasaine of the XLFORUM http://xlforum.net/forums/showthread.php?t=716217)) \\ | + | Finally everything was sanded with 220 wet sand, then polished. ((photos by rasaine of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-accessories/89297-custom-made-heel-toe-shifter?t=716217)) \\ |
| </blockquote> | </blockquote> | ||
| **Version 2**: \\ | **Version 2**: \\ | ||
| Line 71: | Line 86: | ||
| The shift peg rail and shift lever arm are now made of 1/2" aluminum and are not laminated. \\ | The shift peg rail and shift lever arm are now made of 1/2" aluminum and are not laminated. \\ | ||
| The overall laminations are reduced from 7 to 4. \\ | The overall laminations are reduced from 7 to 4. \\ | ||
| - | The orientation of the shift pegs to the foot rest is the exact same as version 2. ((photos by rasaine of the XLFORUM http://xlforum.net/forums/showthread.php?t=716217&page=2)) \\ | + | The orientation of the shift pegs to the foot rest is the exact same as version 2. ((photos by rasaine of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-accessories/89297-custom-made-heel-toe-shifter/page2?t=716217&page=2)) \\ |
| **Version 3**: \\ | **Version 3**: \\ | ||
