Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:body30t [2019/06/22 23:50] hippysmack created |
techtalk:ref:body30t [2022/03/09 05:02] ixl2relax [REF: Body Parts - Sub-01T] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| - | ====== REF: Body Parts - Sub-01R ====== | + | ====== REF: Body Parts - Sub-30T ====== |
| ====== Kickstand Mods ====== | ====== Kickstand Mods ====== | ||
| + | ====== Kickstand Riser ====== | ||
| + | |||
| This mod was devised after lowering the shocks on a standard 2000 XLH and having to lean the a long way to the right to put the jiffy stand down. \\ | This mod was devised after lowering the shocks on a standard 2000 XLH and having to lean the a long way to the right to put the jiffy stand down. \\ | ||
| The OEM kickstand was replaced with a Hugger (advertised 1" shorter than stock). \\ | The OEM kickstand was replaced with a Hugger (advertised 1" shorter than stock). \\ | ||
| Line 10: | Line 12: | ||
| |{{:techtalk:ref:body:jiffy_stand_riser_1_by_aussiegazza.jpg?direct&300|}}|{{:techtalk:ref:body:jiffy_stand_riser_2_by_aussiegazza.jpg?direct&300|}}|{{:techtalk:ref:body:jiffy_stand_riser_3_by_aussiegazza.jpg?direct&300|}}| | |{{:techtalk:ref:body:jiffy_stand_riser_1_by_aussiegazza.jpg?direct&300|}}|{{:techtalk:ref:body:jiffy_stand_riser_2_by_aussiegazza.jpg?direct&300|}}|{{:techtalk:ref:body:jiffy_stand_riser_3_by_aussiegazza.jpg?direct&300|}}| | ||
| + | Here's a used hockey puck bolted to the stand. \\ | ||
| + | |||
| + | {{:techtalk:ref:body:jiffy_stand_mod_by_harley506d.jpg?direct&300|}} ((photo by harley506d of the XLFORUM, cropped by Hippysmack http://xlforum.net/forums/showthread.php?t=2071579)) \\ | ||
| + | ====== Kickstand Extension ====== | ||
| + | {{:techtalk:ref:body:kickstand_extension_toejam503.jpg?direct&300|}} ((photo by Toejam503 of the XLFORUM http://xlforum.net/forums/showthread.php?p=5712103&highlight=heel+toe#post5712103)) \\ | ||
| + | |||
| + | ---- | ||
| + | |||
| + | This one started out with a hole drilled into the end of the stand by the P.O. ((tigercreek of the XLFORUM http://xlforum.net/forums/showthread.php?t=969794)) \\ | ||
| + | When looking to modify the jiffy stand with the aftermarket kits they all say "Except Hugger". \\ | ||
| + | That's true IF you follow the directions. Here's what was done to take the original owner's mod a step further. \\ | ||
| + | {{:techtalk:ref:body:kickstand_mod_1_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM http://xlforum.net/forums/showthread.php?t=969794)) \\ | ||
| + | |||
| + | The kits want you to drill near the shaft/foot of the Jiffy Stand. If you try to attach from there with a Hugger the stand will not completely retract. \\ | ||
| + | However, if you drill/attach through the foot, you can install it to retract and be completely out of the way. \\ | ||
| + | There is no clearance issues and it sits in there pretty tight. \\ | ||
| + | Without the original hole drilled, you could purchase the extender and tape it to several different spots to find the "perfect" placement. \\ | ||
| + | {{:techtalk:ref:body:kickstand_mod_2_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM http://xlforum.net/forums/showthread.php?t=969794)) {{:techtalk:ref:body:kickstand_mod_3_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM http://xlforum.net/forums/showthread.php?t=969794)) {{:techtalk:ref:body:kickstand_mod_4_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM http://xlforum.net/forums/showthread.php?t=969794)) \\ | ||
| \\ | \\ | ||
