Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:carb01j [2019/09/10 00:26] hippysmack [Throttle Cable] |
techtalk:ref:carb01j [2019/09/16 03:29] hippysmack [Mounting a Mikuni VM-38] |
||
---|---|---|---|
Line 36: | Line 36: | ||
These type metal adapters are also available. ((photos by GA_Ironhead of the XLFORUM http://xlforum.net/forums/showpost.php?p=2163034&postcount=5)) \\ | These type metal adapters are also available. ((photos by GA_Ironhead of the XLFORUM http://xlforum.net/forums/showpost.php?p=2163034&postcount=5)) \\ | ||
+ | (Right) - Carb Adapter, HRS-42 and OEM CV Carb To S-and-S Super E Manifold. ((https://secure.vulcanworks.net/store/Carb-Adapter-HRS-42-and-OEM-CV-Carb-To-S-and-S-Super-E-Manifold.html)) \\ | ||
{{:techtalk:ref:carb:press-on_carb_adapter.jpg?direct&300|}} {{:techtalk:ref:carb:non_press_carb_adapter.jpg?direct&300|}} | {{:techtalk:ref:carb:press-on_carb_adapter.jpg?direct&300|}} {{:techtalk:ref:carb:non_press_carb_adapter.jpg?direct&300|}} | ||
Line 124: | Line 125: | ||
====== Throttle Cable ====== | ====== Throttle Cable ====== | ||
+ | This is IronMick's drawing of a new throttle cable made for the Mikuni VM38-9 on a 1978 with stock low buckhorn handlebars. \\ | ||
+ | The universal cable made by Barnett for this application is Barnett part number 101-31-30901. \\ | ||
+ | It is described as a 38" cable, and is about 4" too long for this bike setup so a new one was made. \\ | ||
+ | <blockquote>I do not understand how they calculate cable length but this must be a 34" cable as it is 4" shorter than the 38". \\ | ||
+ | Here is the spec diagram for the 4" shorter throttle cable; if you need to get one special made you can use this as a guide.</blockquote> ((IronMick)) \\ | ||
+ | Note that the two 90° fittings are not the same. The one to the right is for the carb, the one to the left is for the throttle at the handlebar. \\ | ||
+ | Click on a pic to enlarge: \\ | ||
+ | |||
+ | {{:techtalk:ref:carb:vm38-9_throttle_cable_specs_by_ironmick_-_shrunken_sized.jpg?direct&400|}} ((drawing by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1644516)) \\ | ||
+ | |||
There are a couple of things you will have to consider regarding a Mikuni installation. First is the throttle control. ((piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) \\ | There are a couple of things you will have to consider regarding a Mikuni installation. First is the throttle control. ((piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) \\ | ||
The Bendix uses a solid wire and the Mikuni needs a flexible braid cable. \\ | The Bendix uses a solid wire and the Mikuni needs a flexible braid cable. \\ |