Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:carb01j [2019/09/10 00:26] hippysmack [Throttle Cable] |
techtalk:ref:carb01j [2024/01/10 18:29] hippysmack |
||
---|---|---|---|
Line 3: | Line 3: | ||
\\ | \\ | ||
====== Mounting a Mikuni VM-38 ====== | ====== Mounting a Mikuni VM-38 ====== | ||
- | With the VM38 there are several things you want to make sure you get with the carb, or purchase separately. ((piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=1286437&page=2)) \\ | + | With the VM38 there are several things you want to make sure you get with the carb, or purchase separately. ((piniongear of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/126559-best-carb-for-kick-only-72-xlch/page2?t=1286437&page=2)) \\ |
The 90° elbow and the correct throttle cable to go with it. The p/n for the cable is either 657-900 or 657-901. \\ | The 90° elbow and the correct throttle cable to go with it. The p/n for the cable is either 657-900 or 657-901. \\ | ||
The cable has a little longer inner cable (or a little shorter housing) due to the length of the elbow. \\ | The cable has a little longer inner cable (or a little shorter housing) due to the length of the elbow. \\ | ||
Line 36: | Line 36: | ||
These type metal adapters are also available. ((photos by GA_Ironhead of the XLFORUM http://xlforum.net/forums/showpost.php?p=2163034&postcount=5)) \\ | These type metal adapters are also available. ((photos by GA_Ironhead of the XLFORUM http://xlforum.net/forums/showpost.php?p=2163034&postcount=5)) \\ | ||
+ | (Right) - Carb Adapter, HRS-42 and OEM CV Carb To S-and-S Super E Manifold. ((https://secure.vulcanworks.net/store/Carb-Adapter-HRS-42-and-OEM-CV-Carb-To-S-and-S-Super-E-Manifold.html)) \\ | ||
{{:techtalk:ref:carb:press-on_carb_adapter.jpg?direct&300|}} {{:techtalk:ref:carb:non_press_carb_adapter.jpg?direct&300|}} | {{:techtalk:ref:carb:press-on_carb_adapter.jpg?direct&300|}} {{:techtalk:ref:carb:non_press_carb_adapter.jpg?direct&300|}} | ||
Line 124: | Line 125: | ||
====== Throttle Cable ====== | ====== Throttle Cable ====== | ||
+ | This is IronMick's drawing of a new throttle cable made for the Mikuni VM38-9 on a 1978 with stock low buckhorn handlebars. \\ | ||
+ | The universal cable made by Barnett for this application is Barnett part number 101-31-30901. \\ | ||
+ | It is described as a 38" cable, and is about 4" too long for this bike setup so a new one was made. \\ | ||
+ | <blockquote>I do not understand how they calculate cable length but this must be a 34" cable as it is 4" shorter than the 38". \\ | ||
+ | Here is the spec diagram for the 4" shorter throttle cable; if you need to get one special made you can use this as a guide.</blockquote> ((IronMick)) \\ | ||
+ | Note that the two 90° fittings are not the same. The one to the right is for the carb, the one to the left is for the throttle at the handlebar. \\ | ||
+ | Click on a pic to enlarge: \\ | ||
+ | |||
+ | {{:techtalk:ref:carb:vm38-9_throttle_cable_specs_by_ironmick_-_shrunken_sized.jpg?direct&400|}} ((drawing by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1644516)) \\ | ||
+ | |||
There are a couple of things you will have to consider regarding a Mikuni installation. First is the throttle control. ((piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) \\ | There are a couple of things you will have to consider regarding a Mikuni installation. First is the throttle control. ((piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) \\ | ||
The Bendix uses a solid wire and the Mikuni needs a flexible braid cable. \\ | The Bendix uses a solid wire and the Mikuni needs a flexible braid cable. \\ |